Installing the acoustic cover for the oil sump
- Insert and position the acoustic cover (1) of the oil pan.
- Secure expanding rivet (1).
- Replace the fir tree clip (2).
Parts: Fir tree clip
- Secure the fir tree clip (2).
- Secure expanding rivet (1).
- Secure expanding rivet (1).
NOTE:
The following step(s) must be performed if the listed component(s) is/are installed.
- Position the transmission oil lines (1) on the bracket (2).
Make sure that the marks (3) have been positioned correctly on the holder (2).
NOTE:
The following step(s) must be performed if the listed component(s) is/are installed.
- Insert and install the holder (1).
NOTE:
The following step(s) must be performed if the listed component(s) is/are installed.
- Tighten down screw (1).
TIGHTENING TORQUE SPECIFICATIONS
| Holder for transmission oil line | ||
| Screw | Tightening torque | 4 Nm |
- Connect and lock the connector (1).
- Make sure the connector (1) engages audibly.
- Insert and install the positive battery cable (3).
- Secure positive battery cable (3) at the clamp (4).
- Tighten the nut (2) hand-tight.
CAUTION:
Improper routing of the positive battery cable.
Risk of short circuits!
Risk of short circuits!
- Route the positive battery cable without abrasions and do not trap.
- Attach the positive battery cable (1) correctly to anti-twist lock (2).
- Tighten nut (3).
TIGHTENING TORQUE SPECIFICATIONS
| Battery positive lead to starter | ||
| M8 | Tightening torque | 13.5 Nm |
Follow-up work
- RAISING FRONT AXLE SUPPORT .
- TIGHTENING THE SCREWS ON THE LEFT AND RIGHT FRONT AXLE SUPPORT .
- INSTALLING THE LEFT-HAND AND RIGHT-HAND CRASH LEVER .
- ATTACHING THE LEFT AND RIGHT SPRING STRUT ON THE WISHBONE ON THE BOTTOM .
- SECURING THE WISHBONE ON THE TOP LEFT AND RIGHT ON THE SWIVEL BEARING .
- REMOVING THE MOBILE LIFTING TABLE .
- IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
- SECURING BRAKE HOSE, FRONT RIGHT AND LEFT .
- SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
- IF INSTALLED: INSTALLING THE SILENCER/STATIONARY HEATING (ADDITIONAL STEPS, PROCESS NUMBER: 31 11 905) .
- INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
- SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
- INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- FASTENING THE FRONT LEFT AND RIGHT SPRING STRUT .
- INSTALLING CLEAN AIR PIPE, TOP .
- INSTALLING INTAKE SILENCER HOUSING .
- INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
- INSTALLING THE SIDE HOOD SEAL ON THE LEFT AND RIGHT .
- INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- INSTALLING ACOUSTIC COVER .
- INSTALLING THE TORSION STRUT LEFT AND RIGHT .
- MEASURING THE RIDE HEIGHT OF THE FRONT AXLE AND ADJUSTING THE NORMAL POSITION .
- TIGHTENING THE SCREW CONNECTION ON THE LEFT AND RIGHT WISHBONE IN THE NORMAL POSITION .
- INSTALLING UNDERBODY PROTECTION AT REAR .
- INSTALLING THE CENTER UNDERBODY PROTECTION .
- INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- INSTALLING FRONT UNDERBODY PROTECTION .
- CONNECTING ALL BATTERY GROUND LEADS .
- TAKING HOOD OUT OF THE SERVICE POSITION .