Section 74 (19 - Engine - Cooling 4.0L Turbo Gas -- 971 - PANAMERA (971))

WARNING: This page is about a different variant/trim than selected.

WM, 190101 Checking Cooling System
- Tools
- Preliminary Work
- Checking Cooling System
- Subsequent Work
WM, 190107 Bleeding The Cooling System
- Preliminary Work
- Bleeding The Cooling System Manually
  - Bleeding The Cooling System Using Piwis Tester
    - Bleeding The Cooling System
- Subsequent Work
WM, 190129 Cleaning The Cooling System
- Preliminary Work
- Cleaning The Cooling System
- Subsequent Work
WM, 190819 Removing And Installing Electric Fan
- Information
WM, 191419 Removing And Installing Temperature Sensor For Fan (V6 Turbo)
- Technical Values
- Preliminary Work
- Removing And Installing Temperature Sensor For Fan
- Subsequent Work
WM, 192019 Removing And Installing Cooling Fan Housing (Radiator Frame)
- Technical Values
- Preliminary Work
- Removing Cooling Fan Housing (Radiator Frame)
- Installing Cooling Fan Housing (Radiator Frame)
- Subsequent Work
WM, 192419 Removing And Installing Front Air Guide
- Preliminary Work
- Removing Front Air Guide
- Installing Front Air Guide
- Subsequent Work
WM, 192419 Removing And Installing Front Air Guide (Cooling-Air Flaps)
- Preliminary Work
- Removing Front Air Guide (Cooling-Air Flaps)
- Installing Front Air Guide (Cooling-Air Flaps)
- Subsequent Work
WM, 193219 Removing And Installing Motor For Cooling-Air Flaps
- Preliminary Work
- Removing Motor For Cooling-Air Flaps
- Installing Motor For Cooling-Air Flaps
- Subsequent Work
WM, 193519 Removing And Installing Cooling-Air Flaps
- Preliminary Work
- Removing Cooling-Air Flaps
- Installing Cooling-Air Flaps
- Subsequent Work
WM, 193817 Draining And Filling Coolant
- Tools
- Tools And Materials
  - Filling Device - Overview And Setup
- Preliminary Work
- Draining Coolant
- Filling Coolant
- Subsequent Work
WM, 194019 Removing And Installing Coolant Reservoir
- Tools
- Technical Values
- Preliminary Work
- Removing Coolant Reservoir
- Installing Coolant Reservoir
- Subsequent Work
WM, 194319 Removing And Installing Bleed Tube
- Technical Values
- Preliminary Work
- Remove Breather Pipe
  - Removing Breather Pipe
- Install Breather Pipe
  - Installing Bleed Tube
- Subsequent Work
WM, 194519 Removing And Installing Additional Coolant Pump (Run-On) (V8 BITURBO)
- Tools
- Technical Values
- Preliminary Work
- Removing Additional Coolant Pump
- Installing Additional Coolant Pump
- Subsequent Work
WM, 195019 Removing And Installing Coolant Pump (V8 BITURBO)
- Technical Values
- Preliminary Work
- Component Information
- Removing Coolant Pump
- Installing Coolant Pump
- Subsequent Work
WM, 195519 Removing And Installing Coolant Regulator Housing (V8 BITURBO)
- Tools
- Technical Values
- Installation Position
- Preliminary Work
- Removing Coolant Regulator Housing
  - Remove Coolant Regulator Housing
- Installing Coolant Regulator Housing
- Subsequent Work
WM, 195819 Removing And Installing Coolant Regulator (Thermostat Insert) (V8 BITURBO)
- Tools
- Technical Values
- Component Information
  - Installation Position Of Coolant Regulator (Thermostat Insert)
- Preliminary Work
- Removing Coolant Regulator (Thermostat Insert)
- Installing Coolant Regulator (Thermostat Insert)
- Subsequent Work
WM, 197019 Removing And Installing Radiator
- Tools
- Technical Values
- Preliminary Work
- Removing Radiator
- Installing Radiator
- Subsequent Work
WM, 197819 Removing And Installing Coolant Temperature Sensor (Radiator Outlet)
- Technical Values
- Component Information
  - Installation Position Of Coolant Temperature Sensor (Radiator Outlet)
- Preliminary Work
- Removing Coolant Temperature Sensor (Radiator Outlet)
- Installing Coolant Temperature Sensor (Radiator Outlet)
- Subsequent Work
WM, 197819 Removing And Installing Coolant Temperature Sensor (Engine Outlet T2) (V8 BITURBO)
- Technical Values
- Component Information
  - Installation Position Of Coolant Temperature Sensor
- Preliminary Work
- Removing Coolant Temperature Sensor
- Installing Coolant Temperature Sensor
- Subsequent Work