Blind Spot Warning (BSW)/Rear Cross Traffic Alert (RCTA)
- Special Tool(S)
- Test Equipment
- Diagnosis
- Diagnostic Trouble Code Chart <BSW-Ecu (Master)>
- Diagnostic Trouble Code Chart <BSW-Ecu (Slave)>
- Diagnostic Trouble Code Procedures
- DTC C2320: Radar failure
- DTC C2322: Mirror IND. SHT.to PWR supply
- DTC C2323: Mirror indicator short to ground
- DTC C2324: Mirror indicator disconnection
- DTC C2325: Radar horizontal misalignment (L); DTC C2326: Radar horizontal misalignment (R)
- DTC C2327: Radar module dirt
- DTC C2328: Radar PWR.supply VOLT. (Below 9V)
- DTC C2329: Radar PWR.supply VOLT (Above 16V)
- DTC C2330: Radar TEMP. (Out of guarantee)
- DTC C2331: Yaw rate signal error
- DTC C2332: Master-Slave communication fail
- DTC C2333: SAS malfunction
- DTC C2334: SAS neutral point not learned
- DTC C2335: Vehicle speed not determined
- DTC C2336: Shift position not determined
- DTC U0101: T/M CAN timeout
- DTC U0121: ABS/ASC CAN timeout
- DTC U0126: SAS CAN timeout
- DTC U0141: ETACS CAN timeout
- DTC U0146: GATEWAY CAN timeout
- DTC U1190: No receive fault detect signal
- DTC U1195: Coding not completed
- Diagnostic Trouble Code Procedures
- DTC C2320: Radar failure
- DTC C2322: Mirror IND. SHT.to PWR supply
- DTC C2323: Mirror indicator short to ground
- DTC C2324: Mirror indicator disconnection
- DTC C2325: Radar horizontal misalignment (L); DTC C2326 Radar horizontal misalignment (R)
- DTC C2327: Radar module dirt
- DTC C2328: Radar PWR.supply VOLT. (Below 9V)
- DTC C2329: Radar PWR.supply VOLT (Above 16V)
- DTC C2330: Radar TEMP. (Out of guarantee)
- DTC C2331: Yaw rate signal error
- DTC C2332: Master-Slave communication fail
- DTC C2333: SAS malfunction
- DTC C2334: SAS neutral point not learned
- DTC C2335: Vehicle speed not determined
- DTC C2336: Shift position not determined
- DTC U0101: T/M CAN timeout
- DTC U0121: ABS/ASC CAN timeout
- DTC U0126: SAS CAN timeout
- DTC U0141: ETACS CAN timeout
- DTC U0146: GATEWAY CAN timeout
- DTC U1190: No receive fault detect signal
- DTC U1195: Coding not completed
- Trouble Symptom Chart
- Trouble Symptom Procedures
- Inspection Procedure 1: Power supply to the BSW-ECU (master) fails [Cannot communicate with BSW-ECU (master) using the scan tool (M.U.T.-IIISE).]
- Inspection Procedure 2: Power supply to the BSW-ECU (slave) fails [Cannot communicate with BSW-ECU (slave) using the scan tool (M.U.T.-IIISE).]
- Inspection Procedure 3: The system is not turned on and off by changing the BSW setting
- Inspection Procedure 4: Although no vehicle is present within a detection area, the blind spot warning light on door mirror illuminates. (illuminates incorrectly)
- Inspection Procedure 5: Although any vehicle is present within a detection area, the blind spot warning light on door mirror does not illuminate. (the system is on)
- Data List Reference Table
- Actuator Test Table
- Special Function Table
- Check At BSW-Ecu Terminal
- BSW-Ecu