LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2016 >> 6 Touring, Standard Trans >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Trim >> Headliner Removal/Installation

Headliner Removal/Installation

  1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.5] .)
  2. Remove the following parts:
    1. Sunroof seaming welt (with sunroof system) (See SUNROOF UNIT REMOVAL/INSTALLATION .)
    2. A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION .)
    3. Sunvisor (See SUNVISOR REMOVAL/INSTALLATION .)
    4. Front map light (See MAP LIGHT REMOVAL/INSTALLATION .)
    5. Assist handle (See ASSIST HANDLE REMOVAL/INSTALLATION .)
    6. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION .)
    7. Front side trim (RH) (with center display) (See FRONT SIDE TRIM REMOVAL/INSTALLATION .)
    8. Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION .)
    9. B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION .)
    10. Adjust anchor cover (See FRONT SEAT BELT REMOVAL/INSTALLATION .)
    11. Upper anchor installation bolt on the seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION .)
    12. B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION .)
    13. Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION .)
    14. Rear seat side back (See REAR SEAT SIDE BACK REMOVAL/INSTALLATION .)
    15. Tire house trim (See TIRE HOUSE TRIM REMOVAL/INSTALLATION .)
    16. C-pillar trim (See C-PILLAR TRIM REMOVAL/INSTALLATION .)
    17. Upper panel (See UPPER PANEL REMOVAL/INSTALLATION .)
    18. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION .)
    19. Console side panel (See CONSOLE SIDE PANEL REMOVAL/INSTALLATION .)
    20. Selector lever knob (ATX) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION .)
    21. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [C66M-R] .)
    22. Shift panel (See SHIFT PANEL REMOVAL/INSTALLATION .)
    23. Front console box (See FRONT CONSOLE BOX REMOVAL/INSTALLATION .)
    24. CD player (See CD PLAYER REMOVAL .) (See CD PLAYER INSTALLATION .)
    25. Side wall (See SIDE WALL REMOVAL/INSTALLATION .)
    26. Front console (See FRONT CONSOLE REMOVAL/INSTALLATION .)
    27. aa. Rear vent duct (See REAR VENT DUCT REMOVAL/INSTALLATION .)
  3. Set the selector lever component aside. (ATX) (Except mexico) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION .)
  4. Set the shift lever component aside. (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [C66M-R] .)
  5. To prevent damage to the headliner, spread a cloth at the position shown in the figure.
    Fig 1: Identifying Cloth On Headliner
    G11012036Courtesy of MAZDA MOTORS CORP.
  6. Disconnect the roof wiring harness connector and remove the roof wiring harness connector clip from the body.
  7. Pull the roof wiring harness out from the A-pillar side. (with center display)
    Fig 2: Pulling Roof Wiring Harness Out From A-Pillar Side
    G11012037Courtesy of MAZDA MOTORS CORP.
  8. Affix protective tape to the position shown in the figure.
    Fig 3: Identifying Protective Tape Fixing Positions
    G11012038Courtesy of MAZDA MOTORS CORP.
  9. Temporarily install the seaming welt shown in the figure to the headliner.
    CAUTION:
    • If fasteners are removed without temporarily installing the seaming welt, the headliner may fall off and the part may be damaged. Before removing fasteners, temporarily install the seaming welt to prevent the headliner from falling off.
    Fig 4: Identifying Seaming Welt, Headliner And Fasteners
    G11012039Courtesy of MAZDA MOTORS CORP.
  10. Remove fasteners.
  11. Partially peel back the seaming welt. Take the headliner out from the opened passenger-side door opening.
  12. Install in the reverse order of removal.
scientia non olet · About LEMON Manuals