LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> IS 250 RWD, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 32 (Interior Panels) >> Roof Headlining >> Removal

Roof Headlining: Removal

WARNING: This page is about a different car, the 2008 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT SEAT HEADREST ASSEMBLY 
  2. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH  (See REMOVAL )
  3. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH  (See REMOVAL )
  4. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH  (See REMOVAL )
  5. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH  (See REMOVAL )
  6. REMOVE FRONT SEAT ASSEMBLY LH  (See REMOVAL )
  7. REMOVE FRONT SEAT HEADREST ASSEMBLY 
  8. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  9. REMOVE FRONT INNER SEAT TRACK BRACKET COVER RH 

    HINT

    Use the same procedure for the RH side and LH side.

  10. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  11. REMOVE REAR INNER SEAT TRACK BRACKET COVER RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  12. REMOVE FRONT SEAT ASSEMBLY RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  13. REMOVE REAR SEAT CUSHION ASSEMBLY  (See REMOVAL )
  14. REMOVE REAR SEAT HEADREST ASSEMBLY LH 
  15. REMOVE REAR SEAT HEADREST ASSEMBLY RH 
  16. REMOVE REAR SEATBACK ASSEMBLY  (See REMOVAL )
  17. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 
  18. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
  19. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY  (See REMOVAL  )
  20. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH  (See REMOVAL  )
  21. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH  (See REMOVAL  )
  22. REMOVE CONSOLE PANEL SUB-ASSEMBLY  (See REMOVAL  )
  23. REMOVE FRONT ASH RECEPTACLE ASSEMBLY  (See REMOVAL  )
  24. REMOVE REAR ASH RECEPTACLE ASSEMBLY  (See REMOVAL  )
  25. REMOVE CONSOLE BOX REGISTER ASSEMBLY  (See REMOVAL  )
  26. REMOVE CONSOLE BOX  (See REMOVAL  )
  27. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY  (See REMOVAL  )
  28. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL  (See REMOVAL  )
  29. REMOVE MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System)  (See REMOVAL )
  30. REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System)  (See REMOVAL )
  31. REMOVE LOWER NO. 3 STEERING WHEEL COVER  (See REMOVAL )
  32. REMOVE LOWER NO. 2 STEERING WHEEL COVER  (See REMOVAL )
  33. REMOVE STEERING PAD  (See REMOVAL )
  34. REMOVE STEERING WHEEL ASSEMBLY  (See REMOVAL )
  35. REMOVE STEERING COLUMN COVER  (See REMOVAL )
  36. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY  (See REMOVAL )
  37. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Put protective tape around the front door scuff plate
    2. Using a molding remover, disengage the 4 clips.
      Fig 1: Putting Protective Tape Around Front Door Scuff Plate
      G05755635Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 7 claws and remove the front door scuff plate LH
    Fig 2: Identifying Claws For Front Door Scuff Plate LH
    G05755636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  39. REMOVE FRONT DOOR OPENING TRIM COVER LH 
    1. Disengage the 4 claws and remove the front door opening trim cover LH
    Fig 3: Identifying Claws For Front Door Opening Trim Cover LH
    G05755637Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. REMOVE FRONT DOOR OPENING TRIM COVER RH 

    HINT

    Use the same procedure for the RH side and LH side.

  41. REMOVE FRONT PILLAR GARNISH LH 
    1. Disengage the 2 clips from the vehicle body.
    2. Cut off the clip < A >
    3. Disengage the guide and remove the front pillar garnish LH.
    4. Remove the clip < A > from the vehicle body
      Fig 4: Identifying Clips
      G05755638Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Protect the curtain shield airbag assembly.
      1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
        NOTE: Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
      Fig 5: Identifying Curtain Shield Airbag Assembly
      G05755639Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  42. REMOVE FRONT PILLAR GARNISH RH 

    HINT:

    Use the same procedure for the RH side and LH side

  43. REMOVE SIDE INSTRUMENT PANEL LH  (See REMOVAL  )
  44. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY  (See REMOVAL  )
  45. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY  (See REMOVAL  )
  46. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY  (See REMOVAL )
  47. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY  (See REMOVAL  )
  48. REMOVE COMBINATION METER ASSEMBLY  (See REMOVAL  )
  49. REMOVE SIDE INSTRUMENT PANEL RH  (See REMOVAL  )
  50. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY  (See REMOVAL  )
  51. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY  (See REMOVAL )
  52. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY  (See REMOVAL  )
  53. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY  (See REMOVAL  )
  54. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY  (See REMOVAL  )
  55. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY  (See REMOVAL  )
  56. REMOVE FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker)  (See REMOVAL )
  57. REMOVE NO. 2 CONSOLE BOX DUCT  (See REMOVAL  )
  58. REMOVE NO. 1 CONSOLE BOX DUCT  (See REMOVAL  )
  59. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY  (See REMOVAL )
  60. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY  (See REMOVAL  )
  61. REMOVE INSTRUMENT PANEL CLIP  (See REMOVAL  )
  62. REMOVE INSTRUMENT PANEL STAY  (See REMOVAL  )
  63. REMOVE NO. 2 FLOOR UNDER COVER  (See REMOVAL )
  64. REMOVE NO. 1 FLOOR UNDER COVER  (See REMOVAL )
  65. REMOVE TAIL EXHAUST PIPE ASSEMBLY  (See REMOVAL )
  66. REMOVE REAR NO. 1 FLOOR PANEL BRACE  (See REMOVAL )
  67. REMOVE FRONT CENTER FLOOR BRACE  (See REMOVAL )
  68. DISCONNECT HEATED OXYGEN SENSOR  (See REMOVAL )
  69. REMOVE FRONT EXHAUST PIPE ASSEMBLY  (See REMOVAL )
  70. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR  (See REMOVAL )
  71. REMOVE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY  (See REMOVAL )
  72. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY  (See REMOVAL )
  73. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Put protective tape around the rear door scuff plate
    2. Using a molding remover, disengage the 2 clips
      Fig 6: Putting Protective Tape Around Rear Door Scuff Plate
      G05755640Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 5 claws and remove the rear door scuff plate LH.
    Fig 7: Identifying Claws For Rear Door Scuff Plate LH
    G05755641Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  74. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  75. REMOVE LAP BELT OUTER ANCHOR COVER LH 
    1. Disengage the 2 claws and remove the lap belt outer anchor cover LH
      Fig 8: Identifying Claws For Lap Belt Outer Anchor Cover LH
      G05755642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  76. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH 
    1. Remove the bolt and separate the front seat outer belt assembly LH.
      Fig 9: Separating Front Seat Outer Belt Assembly LH
      G05755643Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  77. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Disengage the 3 claws and 5 clips, and remove the lower center pillar garnish LH.
      Fig 10: Identifying Claws And Clips For Lower Center Pillar Garnish LH
      G05755644Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  78. REMOVE CENTER PILLAR GARNISH LH 
    1. Remove the 2 screws.
    2. Disengage the 2 claws and remove the center pillar garnish LH by pulling it down
      Fig 11: Identifying Claws For Center Pillar Garnish LH
      G05755645Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  79. REMOVE FRONT SEAT BELT ANCHOR COVER SUB-ASSEMBLY 
    1. Disengage the 3 claws and remove the front seat belt anchor cover sub-assembly.
    Fig 12: Removing Front Seat Belt Anchor Cover Sub-Assembly
    G05755646Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  80. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT

    Use the same procedure for the RH side and LH side.

  81. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Disconnect the connector.
    2. Remove the bolt and separate the front seat outer belt assembly RH.
    Fig 13: Separating Front Seat Outer Belt Assembly RH
    G05755647Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  82. REMOVE CENTER PILLAR GARNISH RH 

    HINT:

    Use the same procedure for the RH side and LH side.

  83. REMOVE REAR SEAT SIDE GARNISH LH 
    1. Disengage the 5 claws and remove the rear seat side garnish LH
    Fig 14: Removing Rear Seat Side Garnish LH
    G05755648Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  84. REMOVE REAR SEAT SIDE GARNISH RH 

    HINT:

    Use the same procedure for the RH side and LH side

  85. REMOVE ROOF SIDE INNER GARNISH LH 
    1. Disengage the 4 clips and claw, and remove the roof side inner garnish LH.
    Fig 15: Removing Roof Side Inner Garnish LH
    G05755649Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  86. REMOVE ROOF SIDE INNER GARNISH RH 

    HINT:

    Use the same procedure for the RH side and LH side

  87. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER  (See REMOVAL )
  88. REMOVE RAIN SENSOR  (See REMOVAL )
  89. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof)  (See REMOVAL )
  90. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof)  (See REMOVAL )
  91. REMOVE SPOT LIGHT ASSEMBLY  (See ROOM LIGHT )
  92. REMOVE COAT HOOK 
    1. Remove the screw and coat hook.

      HINT

      Use the same procedure to remove the hook on the other side

  93. REMOVE ASSIST GRIP SUB-ASSEMBLY 
    1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers
      Fig 16: Removing Screw And Coat Hook
      G05755650Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 17: Removing Assist Grip Sub-Assembly
      G05755651Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT

      Tape the screwdriver tip before use

    2. Disengage the 2 clips and remove the assist grip sub-assembly

      HINT

      Use the same procedure for the other 3 assist grips

  94. REMOVE VISOR BRACKET COVER 
    1. Using a molding remover, disengage the 4 claws and remove the visor bracket cover

      HINT:

      Use the same procedure to remove the cover on the other side.

      Fig 18: Identifying Claws For Visor Bracket Cover
      G05755652Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  95. REMOVE VISOR ASSEMBLY LH 
    1. Remove the 2 screws and visor assembly LH
    Fig 19: Removing Screws And Visor Assembly LH
    G04946719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  96. REMOVE VISOR ASSEMBLY RH 

    HINT:

    Use the same procedure for the RH side and LH side

  97. REMOVE VISOR HOLDER 
    1. Remove the visor holder by turning it counterclockwise

      HINT

      Use the same procedure to remove the holder on the other side.

      Fig 20: Removing Visor Holder
      G05755654Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  98. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) 
    1. Disconnect the roof wire connector and disengage each clamp from the front pillar LH
    2. Disconnect each connector from the map light assembly
      Fig 21: Identifying Clamp For Front Pillar LH
      G05755655Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the hook, 10 claws and 2 clips.
      Fig 22: Identifying Claws And Clips
      G05755656Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the roof headlining assembly from the vehicle through the front right door
      Fig 23: Removing Roof Headlining Assembly From Vehicle Through Front Right Door
      G05755657Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  99. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) 
    1. Disconnect the roof wire connector and disengage each clamp from the front pillar LH.
    2. Disconnect each connector from the map light assembly
      Fig 24: Identifying Clamp For Front Pillar LH
      G05755655Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the hook, 10 claws, 8 fasteners and 2 clips
      Fig 25: Identifying Claws, Fasteners And Clips
      G05755659Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the roof headlining assembly from the vehicle through the front right door.
      Fig 26: Removing Roof Headlining Assembly From Vehicle Through Front Right Door
      G05755660Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  100. REMOVE ROOF HEADLINING PAD 
    1. Remove the 2 roof headlining pads.
      Fig 27: Removing Roof Headlining Pads
      G05755661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  101. REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof) 
    1. Remove the No. 1 roof silencer pad
      Fig 28: Identifying No. 1 Roof Silencer Pad (W/O Sliding Roof)
      G05755662Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  102. REMOVE CENTER ROOF SILENCER PAD (w/o Sliding Roof) 
    1. Remove the center roof silencer pad
      Fig 29: Identifying Center Roof Silencer Pad (W/O Sliding Roof)
      G05755663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  103. REMOVE ROOF HEADLINING PAD LH (w/o Sliding Roof) 
    1. Remove the 2 roof headlining pads LH
      Fig 30: Identifying Roof Headlining Pad LH (W/O Sliding Roof)
      G05755664Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  104. REMOVE REAR ROOF SILENCER PAD (w/o Sliding Roof) 
    1. Remove the 2 rear roof silencer pads
      Fig 31: Identifying Rear Roof Silencer Pad (W/O Sliding Roof)
      G05755665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  105. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof) 
    1. Remove the rear No. 2 side rail spacer LH.
    Fig 32: Identifying Rear No. 2 Side Rail Spacer RH (W/O Sliding Roof)
    G05755666Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  106. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof) 

    HINT:

    Use the same procedure for the RH side and LH side.

  107. REMOVE REAR SIDE RAIL SPACER LH (w/ Sliding Roof) 
    1. Remove the rear side rail spacer LH
  108. REMOVE REAR SIDE RAIL SPACER RH (w/ Sliding Roof) 

    HINT

    Use the same procedure for the RH side and LH side

    Fig 33: Identifying Rear Side Rail Spacer LH (W/ Sliding Roof)
    G05755667Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  109. REMOVE NO. 2 ROOF HEADLINING PAD 
    1. Remove the 2 No 2 roof headlining pads
      Fig 34: Identifying No. 2 Roof Headlining Pad
      G05755668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  110. REMOVE VANITY LIGHT ASSEMBLY 
    1. Disengage the claw < A > and separate the bulb holder from the vanity light, as shown in the illustration.
    2. Disengage the claw < B > and remove the vanity light assembly.

      HINT

      Use the same procedure to remove the light on the other side

      Fig 35: Removing Vanity Light Assembly
      G05755669Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  111. REMOVE NO. 1 ROOF WIRE 
    1. Remove the double-sided tape and roof wire.
  112. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
  113. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
  114. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 
  115. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 
scientia non olet · About LEMON Manuals