Installing the acoustic cover for the oil sump

• Insert and position the acoustic cover (1)  of the oil pan.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .
• Replace the fir tree clip (2)  .

  Parts:  Fir tree clip

• Secure the fir tree clip (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the transmission oil lines (1)  on the bracket (2)  .

  Make sure that the marks (3)  have been positioned correctly on the holder (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install the holder (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Holder for transmission oil line
  Screw	Tightening torque	4 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the connector (1)  .
• Make sure the connector (1)  engages audibly.
• Insert and install the positive battery cable (3)  .
• Secure positive battery cable (3)  at the clamp (4)  .
• Tighten the nut (2)  hand-tight.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach the positive battery cable 1 correctly  to anti-twist lock (2)  .
• Tighten nut (3)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Battery positive lead to starter
  M8	Tightening torque	13.5 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to RAISING THE FRONT AXLE SUPPORT AND FASTENING IT .
• Refer to INSTALLING THE LEFT AND RIGHT CRASH LEVER .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to CONNECTING THE CONNECTOR ON THE RIDE HEIGHT SENSOR AT THE FRONT .
• Refer to FASTENING WIRING HARNESS TO THE EPS .
• Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
• Refer to FASTENING THE COOLANT LINE .
• Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE TORSION STRUT LEFT AND RIGHT .
• Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
• Refer to INSTALLING COVERS AT FRONT BOTTOM ON LEFT AN RIGHT SIDES .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to REMOVING THE ENGINE FROM THE INSTALLATION POSITION .
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING THE RIGHT FRONT-END STRUT .
• Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to TIGHTENING THE SCREW CONNECTION FOR THE TENSION STRUT ON THE FRONT SUBFRAME ON THE LEFT AND RIGHT .
• Refer to MEASURING THE RIDE HEIGHT OF THE FRONT AXLE AND ADJUSTING THE NORMAL POSITION .
• Refer to ACTIVATING VEHICLE-SPECIFIC HIGH-VOLTAGE OR LOW-VOLTAGE VEHICLE ELECTRICAL SYSTEM .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .