Install front axle differential

Check the O-ring 1 and replace with new O-ring if necessary.

Coat the O-ring 1 with front axle transmission oil.

Courtesy of BMW OF NORTH AMERICA, INC.

Position front axle differential 3.

Make sure marked screws are installed in correct installation locations: 

• Bolts (1) M12x55
• Bolt (2) M12x105

Tighten down screws (1) and (2).

Front axle final drive to motor oil pan, M12 bolts tightening torque: 140 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work: 

• Refer to SECURING THE JUNCTURE SHAFT IN FRONT ON THE FRONT AXLE DIFFERENTIAL .
• Refer to FASTENING ACOUSTIC COVER ON THE OIL PAN .
• Refer to REPLACING THE LEFT AND RIGHT RADIAL SHAFT SEAL .
• Refer to INSTALLING THE FRONT AXLE SUPPORT (RAISE) AND FASTEN .
• Refer to INSTALLING OUTPUT SHAFT ON LEFT AND RIGHT .
• Refer to TOPPING UP/CHECKING FRONT AXLE DIFFERENTIAL OIL .
• Refer to ATTACHING THE RIGHT AND LEFT TENSION STRUTS ON THE SWIVEL BEARING .
• Refer to SECURING THE WISHBONE ON THE LEFT AND RIGHT ON THE SWIVEL BEARING .
• Refer to ATTACHING THE RIGHT AND LEFT OUTPUT SHAFT ONTO THE WHEEL BEARING .
• Refer to SECURING THE TIE ROD TO THE RIGHT AND LEFT ON THE SWIVEL BEARING .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
• Refer to FASTENING ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT .
• Refer to IF INSTALLED: CONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
• Refer to IF INSTALLED: CONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
• Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR
• Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
• Refer to INSTALLING STEERING SHAFT AT BOTTOM ON STEERING GEAR
• Refer to LOWERING THE ENGINE AND DETACHING THE ENGINE BRIDGE
• Refer to FASTENING THE ENGINE SUPPORT BRACKETS TO THE ENGINE MOUNTS ON THE LEFT AND RIGHT .
• Refer to INSTALLING FUEL DELIVERY LINE
• Refer to INSTALLING ALL IGNITION COILS .
• Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to INSTALLING ACOUSTIC COVER AT REAR .
• Refer to INSTALLING THE COWL UPPER PART .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY
• Refer to INSTALLING BATTERY COVER IN TRUNK .
• Refer to CONNECTING THE NEGATIVE BATTERY CABLE (12 V BATTERY) .
• Refer to ACTIVATING HIGH-VOLTAGE SYSTEM
• Refer to INSTALLING FLAP IN RIGHT LUGGAGE COMPARTMENT TRIM PANEL .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .