Section 121 (Chassis Electrical - Lancer Evolution (5 Of 5))
WARNING: This page is about a different car, the 2008 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- ETACS
- Special Tool
- Notes
- Troubleshooting
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnosis Trouble Code Procedures
- DTC U0001: Bus Off (Can-C); DTC U0019: Bus Off (Can-B)
- DTC U0100: Engine Control Module Can Timeout
- DTC U0101: TC-SST-Ecu Can Timeout
- DTC U0103: Shift Lever Can Timeout
- DTC U0121: ASC-Ecu Can Timeout
- DTC U0126: Steering Wheel Sensor Can Timeout
- DTC U0136: S-AWC-Ecu Can Timeout
- DTC U0151: SRS-Ecu Can Timeout
- DTC U0154: Occupant Classification-Ecu Can Timeout
- DTC U0155: Combination Meter Can Timeout
- DTC U0164: A/C-Ecu Can Timeout
- DTC U0168: WCM Or Kos-Ecu Can Timeout
- DTC U0184: Audio Can Timeout
- DTC U0195: Satellite Radio Tuner Can Timeout
- DTC U0197: Hands Free Module Can Timeout
- DTC U0245: Can Box Unit Can Timeout
- DTC U1108: Excess Can-B Ecu Detection
- DTC U1120: Bus Line (Can-C) Low Input; DTC U1121: Bus Line (Can-C) High Input
- DTC U0331: Ecu Internal Error
- DTC B1761: VIN Not Recorded
- DTC B210A: +B Power Supply (Low Input); DTC B210B: +B Power Supply (High Input)
- DTC B222C: Coding Incomplete
- DTC B2206: Chassis Number Does Not Match
- DTC B2215: Ecu Internal Error
- DTC B2353: Ignition Power Supply (Low Input); DTC B2354: Ignition Power Supply (High Input)
- Service Data
- Trouble Symptom Chart
- Symptom Procedures
- Trouble Symptom Chart For Input Signal
- Input Signal Procedures
- Inspection Procedure 1: ETACS-Ecu Does Not Receive Any Signal From The Ignition Switch (Acc)
- Inspection Procedure 2: ETACS-Ecu Does Not Receive Any Signal From The Ignition Switch (IG1)
- Inspection Procedure 3: ETACS-Ecu Does Not Receive Any Signal From The Key Reminder Switch
- Inspection Procedure 4: ETACS-Ecu Does Not Receive Any Signal From The Front Door Lock Actuator
- Inspection Procedure 5: ETACS-Ecu Does Not Receive Any Signal From The Front Door Switch (LH)
- Inspection Procedure 6: ETACS-Ecu Does Not Receive Any Signal From The Front Door Switch (RH)
- Inspection Procedure 7: ETACS-Ecu Does Not Receive Any Signal From The Rear Door Switch (LH)
- Inspection Procedure 8: ETACS-Ecu Does Not Receive Any Signal From The Rear Door Switch (RH)
- Inspection Procedure 9: ETACS-Ecu Does Not Receive Any Signal From The Trunk Lid Latch
- Inspection Procedure 10: ETACS-Ecu Does Not Receive Any Signal From The Hazard Warning Light Switch
- Inspection Procedure 11: ETACS-Ecu Does Not Receive Any Signal From The Column Switch Signal
- Inspection Procedure 12: ETACS-Ecu Does Not Receive Any Signal From The Hood Switch
- On-Vehicle Service
- ETACS-Ecu
- Special Tool
- Theft Alarm
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: The Theft-Alarm Is Not Armed (The Theft-Alarm Indicator Does Not Illuminate)
- Inspection Procedure 2: The Interior Alarm Does Not Work Normally While The Theft-Alarm Is Triggered
- Inspection Procedure 3: Theft-Alarm Horn Does Not Sound While The Theft-Alarm System Is Triggered
- Inspection Procedure 4: Horn (High Or Low) Does Not Sound While The Theft-Alarm System Is Triggered
- Removal And Installation
- Inspection
- Panic Alarm
- Defogger