Section 52 (Heating, Air Conditioning And Ventilation - Lancer Evolution)
WARNING: This page is about a different car, the 2012 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- Fastener Tightening Specifications
- General Specifications
- Service Specifications
- Lubricants
- Service Precautions
- Auto A/C Diagnosis
- Introduction To Heater, A/C And Ventilation Diagnosis
- Heater, A/C And Ventilation Diagnostic Troubleshooting Strategy
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B10C0, B10C1: Interior Temperature Sensor System
- DTC B1000: Control Panel Communication Error
- DTC B1000: Control Panel Communication Error
- DTC B1003: Mode Dial SW Error
- DTC B1003: Mode Dial SW Error
- DTC B1018: Temperature Control Dial SW Error
- DTC B1018: Temperature Control Dial SW Error
- DTC B1021: Fan Dial SW Error
- DTC B1021: Fan Dial SW Error
- DTC B1031, B1032: Fin Thermo Sensor System
- DTC B1031, B1032: Fin Thermo Sensor System
- DTC B1034, B1035: Ambient Air Temperature Sensor System
- DTC B1079: Refrigerant Leaks
- DTC B2214: Control Panel Failure
- DTC B2214: Control Panel Failure
- DTC B223B: Control Panel Improperly Assembled
- DTC B223B: Control Panel Improperly Assembled
- DTC U1415: Coding Not Completed
- DTC U0019: Bus Off (CAN1)
- DTC U0141: ETACS-ECU Time-Out
- DTC U0151: SRS-ECU Time-Out
- DTC U0154: Occupant Classification ECU Time-Out
- DTC U0155: Combination Meter Time-Out
- DTC U0168: WCM Time-Out
- DTC U0184: Audio Time-Out
- DTC U0195: Satellite Radio Tuner Time-Out
- DTC U0245: Audio Visual Navigation Unit CAN Time-Out
- SYMPTOM CHART - Vehicles Without A/C
- Symptom Procedures - Vehicles Without A/C
- INSPECTION PROCEDURE 1: Malfunction Of The Heater Control Unit Power Supply System
- INSPECTION PROCEDURE 2: Blower Fan And Motor Do Not Turn
- INSPECTION PROCEDURE 3: Blower Air Amount Cannot Be Changed
- INSPECTION PROCEDURE 4: Outside/Inside Air Changeover Is Not Possible
- INSPECTION PROCEDURE 5: A/C Outlet Air Temperature Does Not Increase
- INSPECTION PROCEDURE 6: Air Outlet Vent Cannot Be Changed
- INSPECTION PROCEDURE 7: Blower Motor Power Supply System
- INSPECTION PROCEDURE 1: Malfunction Of The Heater Control Unit Power Supply System
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When The A/C Is Operation, Temperature Inside The Passenger Compartment Does Not Decrease (Cool Air Is Not Emitted)
- INSPECTION PROCEDURE 2: Malfunction Of The A/C-ECU Power Supply System
- INSPECTION PROCEDURE 3: The Compressor Does Not Work
- INSPECTION PROCEDURE 4: Blower Fan And Motor Do Not Turn
- INSPECTION PROCEDURE 5: Blower Air Amount Cannot Be Changed
- INSPECTION PROCEDURE 6: Outside/Inside Air Changeover Is Not Possible
- INSPECTION PROCEDURE 7: A/C Outlet Air Temperature Does Not Increase
- INSPECTION PROCEDURE 8: Air Outlet Vent Cannot Be Changed
- INSPECTION PROCEDURE 9: Blower Motor Power Supply System
- Data List Reference Table
- Actuator Test
- Check At A/C-Ecu Terminal
- Special Tools
- On-Vehicle Service
- Heater Control Unit
- Heater Unit And Blower Assembly
- Motors And Transistor
- Ambient Air Temperature Sensor
- Interior Temperature Sensor
- A/C-Ecu
- Compressor Assembly
- Condenser Assembly
- Refrigerant Line
- Ducts
- Ventilators