Rear Axle - 253 Chassis - 2 Of 2
- Testing & Repair
- Check Oil Level In Rear Axle Differential, Correct If Necessary - AR35.31-P-0520-08MNA
- Remove/Install Differential - AR35.31-P-0520LW
- Remove/Install Rear Axle Differential - AR35.31-P-0522MNA
- Drain/Fill Rear Axle Gear Oil - AR35.31-P-0523LW
- Measure And Note Down Total Friction Torque Of Drive Pinion - AR35.31-P-0530-04CWC
- Install New Radial Sealing Ring At Drive Pinion Gear (With Differential Installed) - AR35.31-P-0530LW
- Replace Radial Shaft Sealing Ring On Drive Pinion - AR35.31-P-0531LWC
- Remove/Install Radial Shaft Sealing Ring Of Rear Axle Shaft On Rear Axle Housing - AR35.31-P-0542LWC
- Replace Radial Sealing Rings On Side Of Rear Axle Center Assembly - AR35.31-P-0545LW
- Pulling Off Joint Flange - AR35.31-P-0550-06CWC
- Adjusting Friction Torque Of Drive Pinion Bearing - AR35.31-P-0550-17CWC
- Remove/Install End Cover At Differential - AR35.31-P-0554LW
- Remove/Install Cover Of Rear Axle Differential
- Remove/Install Differential Lock Actuator Motor - AR35.40-P-7400LW
- Test & Adjustment Values
- Maintenance
- Capacities & Specifications
- Torque Specifications
- Tightening Torques: Passenger Cars: Rear Axle - BA35.00-Z-9999AZ
- Rear Axle Carrier - BA35.10-P-1000-01H
- Spring Control Arm - BA35.20-P-1000-01I
- Camber Strut - BA35.20-P-1000-02L
- Torque Strut - BA35.20-P-1000-03L
- Tie Rod - BA35.20-P-1000-04M
- Thrust Arm - BA35.20-P-1000-05J
- Hub - BA35.20-P-1000-06E
- Rear Axle Shaft - BA35.30-P-1000-01N
- Rear Axle Differential Housing - BA35.31-P-1000-02H
- Rear Axle Differential Gear Set - BA35.31-P-1000-06B
- Differential Lock - BA35.40-P-1000-02A
- Special Tools
- 001 589 49 21 00 Torque Measuring Instrument - WS35.00-P-0009B
- 211 589 00 61 00 Assembly Tool - WS35.00-P-0026B
- 205 589 00 15 00 Drift - WS35.00-P-0029B
- 205 589 00 43 00 Extraction And Insertion Tool - WS35.00-P-0033C
- 116 589 15 15 00 Drift - WS35.00-P-0038C
- 204 589 01 09 00 Socket Wrench Bit - WS35.00-P-0039B
- 204 589 00 15 00 Drift - WS35.00-P-0042B
- 129 589 01 07 00 Pin Wrench - WS35.00-P-0071B
- 129 589 01 33 00 Puller - WS35.00-P-0072B
- 202 589 00 43 00 Removal And Installation Tool - WS35.00-P-0143C
- 140 589 08 15 00 Drift - WS35.00-P-0148B
- 140 589 10 15 00 Drift - WS35.00-P-0149C
- 202 589 04 43 07 Plate - WS35.00-P-0153-01C
- 202 589 04 43 10 Press - WS35.00-P-0153-03C
- 202 589 04 43 00 Extraction Tool - WS35.00-P-0153C
- 210 589 03 43 09 Pin - WS35.00-P-0154-01C
- 210 589 03 43 00 Extraction And Insertion Tool - WS35.00-P-0154C
- 210 589 01 40 00 Bracket - WS35.00-P-0160C
- 220 589 01 43 12 Threaded Spindle - WS35.00-P-0171-01B
- 220 589 01 43 00 Removal And Installation Tool - WS35.00-P-0171B
- 220 589 02 31 00 Clamping Jaws - WS35.00-P-0175B
- 140 589 14 15 00 Drift - WS35.00-P-0191C
- 205 589 01 43 00 Extraction And Insertion Tool - WS35.00-P-0208B
- 119 589 00 10 00 Screwdriver Bit - WS35.00-P-0228B
- 211 589 04 15 00 Drift - WS35.00-P-0235B
- 203 589 01 14 00 Sleeve - WS35.00-P-0237C
- 221 589 01 43 00 Extraction And Installation Tool - WS35.00-P-0244B
- 001 589 01 63 00 Securing Belt - WS35.00-P-0251B
- 001 589 51 33 00 Hollow Piston Cylinder - WS35.00-P-0252B
- 220 589 01 09 00 Socket Wrench Bit - WS35.00-P-0253B
- 204 589 01 43 00 Extraction And Insertion Tool - WS35.00-P-0259B
- 204 589 04 43 00 Extraction And Insertion Tool - WS35.00-P-0260B
- 204 589 00 43 00 Extraction And Insertion Tool - WS35.00-P-0261B
- 204 589 02 43 00 Insertion Tool - WS35.00-P-0262B
- 204 589 03 43 00 Extraction And Insertion Tool - WS35.00-P-0263B