Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
NOTE:
Unlisted Diagnostic Trouble Codes (DTCs) are often retrieved as a result of incorrect repair procedures. Before attempting any repairs for unlisted Diagnostic Trouble Codes (DTCs), check the vehicle service history for recent repairs. For RCM Diagnostic Trouble Codes (DTCs) not listed in this chart,
- Repair all other RCM Diagnostic Trouble Codes (DTCs) before attempting to repair any Diagnostic Trouble Codes (DTCs) not listed in this chart.
- If no other RCM Diagnostic Trouble Codes (DTCs) are retrieved, CLEAR the RCM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the RCM Diagnostic Trouble Codes (DTCs) return, VERIFY that the RCM is the correct part number for the vehicle application, and INSTALL As-Built data following scan tool instructions under Module Programming > As-Built.
- Inspect the RCM and RCM connectors for any damaged pins or connections.
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B00A0:11 | Occupant Classification System: Circuit Short to Ground | GO to Pinpoint Test BS |
| BCM | B00A0:12 | Occupant Classification System: Circuit Short to Battery | GO to Pinpoint Test BS |
| BCM | B1123:11 | Restraints Ignition Relay: Circuit Short to Ground | GO to Pinpoint Test BS |
| BCM | B1123:12 | Restraints Ignition Relay: Circuit Short to Battery | GO to Pinpoint Test BS |
| BCM | B11D8:01 | Restraint Event Notification: General Electrical Failure | GO to Pinpoint Test W |
| OCSM | B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test BE |
| OCSM | B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test BE |
| OCSM | B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test BE |
| OCSM | B0061:64 | Passenger Seatbelt Tension Sensor: Signal Plausibility Failure | GO to Pinpoint Test BE |
| OCSM | B00A0:62 | Occupant Classification System: Signal Compare Failure | GO to Pinpoint Test BF |
| OCSM | B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Ground | GO to Pinpoint Test BG |
| OCSM | B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery | GO to Pinpoint Test BG |
| OCSM | B00C0:16 | Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold | GO to Pinpoint Test BG |
| OCSM | B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | GO to Pinpoint Test BG |
| OCSM | B00C0:7B | Passenger Seat Occupant Classification Sensor "A": Low Fluid Level | GO to Pinpoint Test BG |
| OCSM | B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to Pinpoint Test BH |
| OCSM | B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to Pinpoint Test BH |
| OCSM | B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test BI |
| OCSM | U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BJ |
| OCSM | U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BK |
| OCSM | U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test BL |
| OCSM | U024C:00 | Lost Communication with Seat Control Module "H": No Sub Type Information | GO to Pinpoint Test BM |
| OCSM | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BN |
| OCSM | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BO |
| OCSM | U0509:00 | Invalid Data Received From "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test BP |
| OCSM | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test BQ |
| OCSM | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test BQ |
| OCSM | U3000:46 | Control Module: Special Memory Failure | GO to Pinpoint Test BQ |
| OCSM | U3000:54 | Control Module: Missing Calibration | GO to Pinpoint Test BR |
| OCSM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BD |
| OCSM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BD |
| RCM | B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test A |
| RCM | B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test A |
| RCM | B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test A |
| RCM | B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test A |
| RCM | B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test B |
| RCM | B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test B |
| RCM | B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test B |
| RCM | B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test B |
| RCM | B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test C |
| RCM | B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test C |
| RCM | B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test C |
| RCM | B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test C |
| RCM | B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0004:4A | Driver Knee Bolster Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0005:11 | Collapsible Steering Column Deployment Control: Circuit Short to Ground | GO to Pinpoint Test D |
| RCM | B0005:12 | Collapsible Steering Column Deployment Control: Circuit Short to Battery | GO to Pinpoint Test D |
| RCM | B0005:13 | Collapsible Steering Column Deployment Control: Circuit Open | GO to Pinpoint Test D |
| RCM | B0005:1A | Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| RCM | B0005:2B | Collapsible Steering Column Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0005:4A | Collapsible Steering Column Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test E |
| RCM | B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test E |
| RCM | B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test E |
| RCM | B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test E |
| RCM | B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test F |
| RCM | B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test F |
| RCM | B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test F |
| RCM | B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test F |
| RCM | B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0013:11 | Passenger Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test G |
| RCM | B0013:12 | Passenger Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test G |
| RCM | B0013:13 | Passenger Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test G |
| RCM | B0013:1A | Passenger Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test G |
| RCM | B0013:2B | Passenger Knee Bolster Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0013:4A | Passenger Knee Bolster Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test H |
| RCM | B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test H |
| RCM | B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to Pinpoint Test H |
| RCM | B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test H |
| RCM | B0050:2B | Driver Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0051:11 | First Row Center Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test I |
| RCM | B0051:12 | First Row Center Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test I |
| RCM | B0051:13 | First Row Center Seatbelt Sensor: Circuit Open | GO to Pinpoint Test I |
| RCM | B0051:1D | First Row Center Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test I |
| RCM | B0051:2B | First Row Center Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0051:4A | First Row Center Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test J |
| RCM | B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test J |
| RCM | B0052:13 | Passenger Seatbelt Sensor: Circuit Open | GO to Pinpoint Test J |
| RCM | B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test J |
| RCM | B0052:2B | Passenger Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0054:11 | Second Row Center Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test K |
| RCM | B0054:12 | Second Row Center Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test K |
| RCM | B0054:13 | Second Row Center Seatbelt Sensor: Circuit Open | GO to Pinpoint Test K |
| RCM | B0054:1D | Second Row Center Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test K |
| RCM | B0054:2B | Second Row Center Seatbelt Sensor: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0054:4A | Second Row Center Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0070:11 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test L |
| RCM | B0070:12 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test L |
| RCM | B0070:13 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test L |
| RCM | B0070:1A | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test L |
| RCM | B0070:2B | Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0070:4A | Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0072:11 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test M |
| RCM | B0072:12 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test M |
| RCM | B0072:13 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test M |
| RCM | B0072:1A | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test M |
| RCM | B0072:2B | Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0072:4A | Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B007E:11 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test N |
| RCM | B007E:12 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test N |
| RCM | B007E:13 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test N |
| RCM | B007E:1A | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test N |
| RCM | B007E:2B | Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B007E:4A | Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B007F:11 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test O |
| RCM | B007F:12 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test O |
| RCM | B007F:13 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test O |
| RCM | B007F:1A | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test O |
| RCM | B007F:2B | Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B007F:4A | Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0080:11 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short To Ground | GO to Pinpoint Test P |
| RCM | B0080:12 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short To Battery | GO to Pinpoint Test P |
| RCM | B0080:13 | Driver Seatbelt Load Limiter Deployment Control: Circuit Open | GO to Pinpoint Test P |
| RCM | B0080:1A | Driver Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test P |
| RCM | B0080:2B | Driver Seatbelt Load Limiter Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B0080:4A | Driver Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | GO to Pinpoint Test Q |
| RCM | B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | GO to Pinpoint Test Q |
| RCM | B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open | GO to Pinpoint Test Q |
| RCM | B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test Q |
| RCM | B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B00A0:09 | Occupant Classification System: Component Failure | GO to Pinpoint Test R |
| RCM | B00A0:4A | Occupant Classification System: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out | GO to Pinpoint Test R |
| RCM | B00A0:64 | Occupant Classification System: Signal Plausibility Failure | GO to Pinpoint Test R |
| RCM | B00A0:68 | Occupant Classification System: Event Information | GO to Pinpoint Test R |
| RCM | B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test S |
| RCM | B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test S |
| RCM | B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test S |
| RCM | B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test S |
| RCM | B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short To Ground | GO to Pinpoint Test T |
| RCM | B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short To Battery | GO to Pinpoint Test T |
| RCM | B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | GO to Pinpoint Test T |
| RCM | B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test U |
| RCM | B11CF:11 | Passenger Frontal Airbag Canister Vent: Circuit Short to Ground | GO to Pinpoint Test V |
| RCM | B11CF:12 | Passenger Frontal Airbag Canister Vent: Circuit Short to Battery | GO to Pinpoint Test V |
| RCM | B11CF:13 | Passenger Frontal Airbag Canister Vent: Circuit Open | GO to Pinpoint Test V |
| RCM | B11CF:1A | Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold | GO to Pinpoint Test V |
| RCM | B11CF:2B | Passenger Frontal Airbag Canister Vent: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B11CF:4A | Passenger Frontal Airbag Canister Vent: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B11D8:11 | Restraint Event Notification: Circuit Short To Ground | GO to Pinpoint Test W |
| RCM | B11D8:12 | Restraint Event Notification: Circuit Short To Battery | GO to Pinpoint Test W |
| RCM | B11D8:13 | Restraint Event Notification: Circuit Short To Open | GO to Pinpoint Test W |
| RCM | B1202:11 | Restraint System Passenger Enable Indicator: Circuit Short To Ground | GO to Pinpoint Test X |
| RCM | B1202:12 | Restraint System Passenger Enable Indicator: Circuit Short To Battery | GO to Pinpoint Test X |
| RCM | B1202:13 | Restraint System Passenger Enable Indicator: Circuit Open | GO to Pinpoint Test X |
| RCM | B1202:4A | Restraint System Passenger Enable Indicator: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1404:11 | Driver Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test Y |
| RCM | B1404:12 | Driver Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test Y |
| RCM | B1404:13 | Driver Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test Y |
| RCM | B1404:1A | Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test Y |
| RCM | B1404:2B | Driver Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B1404:4A | Driver Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1405:11 | Driver Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test Z |
| RCM | B1405:12 | Driver Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test Z |
| RCM | B1405:13 | Driver Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test Z |
| RCM | B1405:1A | Driver Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test Z |
| RCM | B1405:2B | Driver Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B1405:4A | Driver Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1407:11 | Passenger Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test AA |
| RCM | B1407:12 | Passenger Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test AA |
| RCM | B1407:13 | Passenger Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test AA |
| RCM | B1407:1A | Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AA |
| RCM | B1407:2B | Passenger Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B1407:4A | Passenger Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1408:11 | Passenger Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test AB |
| RCM | B1408:12 | Passenger Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test AB |
| RCM | B1408:13 | Passenger Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test AB |
| RCM | B1408:1A | Passenger Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test AB |
| RCM | B1408:2B | Passenger Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AN |
| RCM | B1408:4A | Passenger Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B140C:11 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test AC |
| RCM | B140C:12 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test AC |
| RCM | B140C:13 | Second Row Driver Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AC |
| RCM | B140C:1D | Second Row Driver Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test AC |
| RCM | B140C:2B | Second Row Driver Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B140C:4A | Second Row Driver Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B140D:11 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test AD |
| RCM | B140D:12 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test AD |
| RCM | B140D:13 | Second Row Passenger Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AD |
| RCM | B140D:1D | Second Row Passenger Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test AD |
| RCM | B140D:2B | Second Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B140D:4A | Second Row Passenger Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1410:11 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AE |
| RCM | B1410:12 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AE |
| RCM | B1410:13 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AE |
| RCM | B1410:1A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AE |
| RCM | B1410:2B | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B1410:4A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1412:11 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AF |
| RCM | B1412:12 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AF |
| RCM | B1412:13 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AF |
| RCM | B1412:1A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AF |
| RCM | B1412:2B | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AN |
| RCM | B1412:4A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1413:11 | Driver Frontal Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test AH |
| RCM | B1413:12 | Driver Frontal Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test AH |
| RCM | B1413:13 | Driver Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AH |
| RCM | B1413:4A | Driver Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1413:81 | Driver Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1413:96 | Driver Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B1414:11 | Driver Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AI |
| RCM | B1414:11 | Driver Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AJ |
| RCM | B1414:12 | Driver Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AI |
| RCM | B1414:12 | Driver Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AJ |
| RCM | B1414:13 | Driver Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AI |
| RCM | B1414:13 | Driver Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AJ |
| RCM | B1414:4A | Driver Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1414:81 | Driver Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1414:96 | Driver Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B1415:11 | Driver Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AL |
| RCM | B1415:12 | Driver Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AL |
| RCM | B1415:13 | Driver Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AL |
| RCM | B1415:4A | Driver Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1415:81 | Driver Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1415:96 | Driver Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B1417:11 | Passenger Frontal Restraints Sensor: Circuit Short To Ground | GO to Pinpoint Test AM |
| RCM | B1417:12 | Passenger Frontal Restraints Sensor: Circuit Short To Battery | GO to Pinpoint Test AM |
| RCM | B1417:13 | Passenger Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AM |
| RCM | B1417:4A | Passenger Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1417:81 | Passenger Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1417:96 | Passenger Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B1418:11 | Passenger Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AK |
| RCM | B1418:11 | Passenger Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AL |
| RCM | B1418:12 | Passenger Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AK |
| RCM | B1418:12 | Passenger Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AL |
| RCM | B1418:13 | Passenger Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AK |
| RCM | B1418:13 | Passenger Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AL |
| RCM | B1418:4A | Passenger Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1418:81 | Passenger Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1418:96 | Passenger Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B1419:11 | Passenger Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AJ |
| RCM | B1419:12 | Passenger Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AJ |
| RCM | B1419:13 | Passenger Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AJ |
| RCM | B1419:4A | Passenger Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1419:81 | Passenger Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AG |
| RCM | B1419:96 | Passenger Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AG |
| RCM | B142D:00 | Pyrotechnic End of Life Activation Performed: No Sub Type Information | GO to Pinpoint Test AZ |
| RCM | B1469:4A | Unused Satellite Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B146A:4A | Unused Satellite Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1492:68 | Fuel Cutoff Event: Event Information | GO to Pinpoint Test BA |
| RCM | B1534:4A | Unused Deployable Device: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | B1535:4A | Unused DC Sensor Device: Incorrect Component Installed | GO to Pinpoint Test AO |
| RCM | C0061:68 | Lateral Acceleration Sensor: Event Information | GO to Pinpoint Test AP |
| RCM | C0062:68 | Longitudinal Acceleration Sensor: Event Information | GO to Pinpoint Test AP |
| RCM | C0063:68 | Yaw Rate Sensor: Event Information | GO to Pinpoint Test AP |
| RCM | C0064:68 | Roll Rate Sensor: Event Information | GO to Pinpoint Test AP |
| RCM | C0065:68 | Vertical Acceleration Sensor: Event Information | GO to Pinpoint Test AP |
| RCM | U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | GO to Pinpoint Test AQ |
| RCM | U0028:88 | Vehicle Communication Bus A: Bus Off | GO to Pinpoint Test AQ |
| RCM | U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BJ |
| RCM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AR |
| RCM | U0131:00 | Lost Communication With Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test AS |
| RCM | U0140:00 | Lost Communication with Body Control Module: No Sub Type Information | GO to Pinpoint Test AT |
| RCM | U0146:00 | Lost Communication with Gateway "A": No Sub Type Information | GO to Pinpoint Test AU |
| RCM | U0154:00 | Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test AV |
| RCM | U023B:00 | Lost Communication With Image Processing Module B: No Sub Type Information | GO to Pinpoint Test AW |
| RCM | U0253:00 | Lost Communication with Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AX |
| RCM | U0300:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AZ |
| RCM | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test AY |
| RCM | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0415:81 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Invalid Serial Data Received | GO to Pinpoint Test AY |
| RCM | U0420:00 | Invalid Data Received from Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0422:56 | Invalid Data Received From Body Control Module: Invalid/Incompatible Configuration | GO to Pinpoint Test AY |
| RCM | U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test AY |
| RCM | U0422:92 | Invalid Data Received From Body Control Module: Performance Or Incorrect Operation | GO to Pinpoint Test AY |
| RCM | U0455:81 | Invalid Data Received From Restraints Occupant Classification System Module: Invalid Serial Data Received | GO to Pinpoint Test AY |
| RCM | U053C:00 | Invalid Data Received From Image Processing Module B: No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AY |
| RCM | U0557:82 | Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AY |
| RCM | U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test BB |
| RCM | U2024:57 | Control Module Cal-Config Data: Invalid/Incompatible Software Component | GO to Pinpoint Test AZ |
| RCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BB |
| RCM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AQ |
| RCM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AZ |
| RCM | U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test BC |
| RCM | U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test BC |
| RCM | U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AZ |
| RCM | U3000:46 | Control Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test AZ |
| RCM | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AZ |
| RCM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BD |
| RCM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BD |