LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Transit Connect Titanium, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different car >> Section 739 (Supplemental Restraint System - Pinpoint Tests A Through M) >> Pinpoint Tests >> Pinpoint Test J: B0052:11, B0052:12, B0052:13, B0052:1D

Pinpoint Test J: B0052:11, B0052:12, B0052:13, B0052:1D

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
  1. Refer to Wiring Diagrams SUPPLEMENTAL RESTRAINT SYSTEM for schematic and connector information.

    Normal Operation and Fault Conditions 

    REFER to: Airbag and Seatbelt Pretensioner Supplemental Restraint System (SRS) - System Operation and Component Description .

    The RCM monitors the passenger seatbelt buckle switch circuits for the following faults:

    • Open circuit
    • Short to voltage
    • Short to ground
    • Current out of range
    • Faulted passenger seatbelt buckle switch

    If a fault is detected, the RCM stores DTC B0052:11, B0052:12, B0052:13 or B0052:1D in memory and sends a message to the IPC to illuminate the airbag warning indicator.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    RCM B0052:11 Passenger Seatbelt Sensor: Circuit Short To Ground A fault is indicated when the RCM senses a short to ground on the passenger seatbelt buckle switch circuit.
    RCM B0052:12 Passenger Seatbelt Sensor: Circuit Short To Battery A fault is indicated when the RCM senses a short to voltage on the passenger seatbelt buckle switch circuit.
    RCM B0052:13 Passenger Seatbelt Sensor: Circuit Open A fault is indicated when the RCM senses an open on either passenger seatbelt buckle switch circuit.
    RCM B0052:1D Passenger Seatbelt Sensor: Circuit Current Out Of Range A fault is indicated when the RCM senses current out of an acceptable range between the passenger seatbelt buckle switch circuits.

    Possible Sources 

    • Wiring, terminals or connectors
    • Passenger seatbelt buckle
    • RCM

  2. WARNING: Incorrect repair techniques or actions can cause an accidental Supplemental Restraint System (SRS) deployment. Never compromise or depart from these instructions. Failure to precisely follow all instructions could result in serious personal injury from an accidental deployment.
  3. NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector.
  4. NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
  5. NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
  6. NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
  7. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

  8. J1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • WARNING: Before beginning any service procedure In this article, refer to Safety warnings in General Information. Failure to follow this instruction may result in serious personal injury.

      REFER to: Pyrotechnic Device Health and Safety Precautions .

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-demand during self-test? 

    Yes  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B0052:11 or B0052:1D, GO to  J2 For DTC B0052:12, GO to  J4 For DTC B0052:13, GO to  J5
    No  This is an intermittent fault when present as a CMDTC only. GO to  J10

  9. J2 CHECK THE PASSENGER SEATBELT SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED)

    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    • Ignition OFF.

    • Disconnect Passenger Seatbelt Buckle C3738.

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seatbelt buckle switch disconnected, an open circuit fault is normally retrieved. Due to the inline connector being disconnected, a fault is also normally retrieved for the passenger seat position sensor and passenger side airbag circuits.

    Did the on-demand DTC change from B0052:11 or B0052:1D to B0052:13? 

    Yes  GO to  J8
    No  For DTC B0052:11, GO to  J3 For DTC B0052:1D, GO to  J9

  10. J3 CHECK THE PASSENGER SEATBELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO GROUND

    • Ignition OFF.

    • Disconnect RCM C310A and C310B.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3738-5
      GFD562389Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  J9
    No  REPAIR the circuit. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to  J11

  11. J4 CHECK THE PASSENGER SEATBELT BUCKLE SWITCH CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition OFF.

    • Disconnect RCM C310A and C310B.

    • Disconnect Passenger Seatbelt Buckle C3738.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3738-5
      GFD562392Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to  J11
    No  GO to  J9

  12. J5 CHECK THE PASSENGER SEATBELT SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED)

    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    • Ignition OFF.

    • Disconnect Passenger Seatbelt Buckle C3738.

    • Connect a fused jumper wire:
      Lead 1 Measurement / Action Lead 2
      C3738-5
      GFD562391Courtesy of FORD MOTOR COMPANY
      		 C3738-6

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seatbelt buckle switch circuits shorted together, a short to ground fault is normally retrieved. Due to the inline connector being disconnected, a fault is also normally retrieved for the passenger seat position sensor and passenger side airbag circuits.

    Did the on-demand DTC change from B0052:13 to B0052:11? 

    Yes  REMOVE the fused jumper wire and GO to  J8
    No  REMOVE the fused jumper wire and GO to  J6

  13. J6 CHECK THE PASSENGER SEATBELT BUCKLE SWITCH CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Disconnect RCM C310A and C310B.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C310B-55
      GFD562389Courtesy of FORD MOTOR COMPANY
      		 C3738-5

    Is the resistance less than 0.5 ohm? 

    Yes  GO to  J7
    No  REPAIR the circuit. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to  J11

  14. J7 CHECK THE PASSENGER SEATBELT BUCKLE SWITCH RETURN CIRCUIT FOR AN OPEN

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3738-6
      GFD562389Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance less than 3 ohms? 

    Yes  GO to  J9
    No  REPAIR the circuit. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to  J11

  15. J8 CONFIRM THE PASSENGER SEATBELT BUCKLE SWITCH FAULT

    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

    • Ignition OFF.

    • Prior to reconnecting any previously disconnected SRS component:

      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
      • repair any concerns found. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B.

    • Connect Passenger Seatbelt Buckle C3738.

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes  INSTALL a new passenger seatbelt buckle. REFER to: Front Seatbelt Buckle . GO to  J11
    No  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  J10

  16. J9 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT

    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

    • Ignition OFF.

    • Prior to reconnecting any previously disconnected SRS component:

      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
      • repair any concerns found. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Connect RCM C310A and C310B.

    • Connect Passenger Seatbelt Buckle C3738.

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . GO to  J11
    No  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  J10

  17. J10 CHECK FOR AN INTERMITTENT FAULT

    • Ignition OFF.

    • Disconnect Passenger Seatbelt Buckle C3738.

      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Repair any concerns found. Refer to Wiring Diagrams OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

    • Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

    • Connect all  previously disconnected components and connectors.

    • Ignition ON.

    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B0052:11, B0052:12, B0052:13 or B0052:1D retrieved on-demand during self-test? 

    Yes  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B0052:11 or B0052:1D, GO to  J2 For DTC B0052:12, GO to  J4 For DTC B0052:13, GO to  J5
    No  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  J11

  18. J11 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Ignition OFF.

    • Connect all  previously disconnected components and connectors.

    • Ignition ON.

    • NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM and OCSM.

      Using a diagnostic scan tool, perform

      Restraints  self-test.

    Are any RCM or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-demand during self-test? 

    Yes  Do not clear any Diagnostic Trouble Codes (DTCs) until all  Diagnostic Trouble Codes (DTCs) have been resolved. DIAGNOSE and REPAIR the SRS Diagnostic Trouble Codes (DTCs). REFER to the DTC Chart In this article.
    No  The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals