Raising the front subframe

• Lift the front subframe (1) with the special tool  2 219 012  .
• Feed in the struts (2).

Courtesy of BMW OF NORTH AMERICA, INC.

• Lift the front subframe using special tools 2 219 012 and 0 495 817 (31 5 251)  and position it on the body.

Courtesy of BMW OF NORTH AMERICA, INC.

• Replace screws (1) to (3).

  Parts:  Screws

• Tighten the screws (3).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Front subframe on front/center of body
  M12 Replace screws.	Tightening torque	108 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the screws (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Front axle carrier to body, rear
  M14 Replace screws.	Tightening torque	120 Nm

• Tighten the screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Front subframe to outer body at the rear
  M10 Replace screws.	Tightening torque  Angle of rotation	56 Nm 90°

  NOTE: Perform the steps on the left and right side.
• Position the adapter on the front subframe.
• Tighten down screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Adapter, front axle support to front axle support
  M8x70	Tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Lower the special tool 0 495 817 (31 5 251)  with the special tool 2 219 012 and place it to the side.

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: Perform the steps on the left and right side.
• Tighten the screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Output shaft passage strut to front subframe
  M10x60	Tightening torque	56 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed the return line (1) for the transmission oil cooler into the holder (2) in the arrow direction and install it.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed the feed line (1) on the holder (2) in the arrow direction and install it.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to ATTACHING THE REINFORCEMENT STRUT TO THE FRONT SUBFRAME .
• Refer to SECURING THE COOLANT LINE TO THE FRONT SUBFRAME .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR .
• Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT SUBFRAME .
• Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE DOUBLE PIVOT .
• Refer to INSTALLING THE LEFT FRONT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING THE LEFT AND RIGHT FRONT UNDERSHIELD .
• Refer to INSTALLING COVERS AT FRONT BOTTOM ON LEFT AN RIGHT SIDES .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE FRONT SPOILER .
• Refer to SECURING THE TRANSMISSION OIL LINES ON THE FRONT SUBFRAME .
• Refer to INSTALLING THE INTAKE FILTER HOUSING ON THE LEFT (FRONT-END STRUT REMOVED) .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .