Installing the eccentric shaft of cylinder bank 1
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW M5, 2022 BMW M5, 2021 BMW M5, 2020 BMW M5, and 2019 BMW M5. However, it is still accessible from the selected car via links, so may be relevant.
- Coat the bearing positions of the eccentric shaft with motor oil.
- Insert the eccentric shaft (2) from below and install.
- Pay attention to the installation locations of the guide bearing shells (E1) to (E5) .
- Position bearing brackets as shown in the illustration.
NOTE:
RISK OF DAMAGE
Contaminant or foreign body.
Contamination can result in malfunctions, loss of function or leaks.
Contaminant or foreign body.
Contamination can result in malfunctions, loss of function or leaks.
- Adhere to the utmost cleanliness.
- Protect components from contamination e.g. by covering.
- Close off line connections with seal plugs.
- Tighten all screws in the marked areas (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Eccentric shaft bearing brackets | ||
|---|---|---|
| Screw M6 | Tightening torque | 10 Nm |
Follow-up work
- Refer to INSTALLING THE ROLLER CAM FOLLOWER OF THE INTAKE CAMSHAFT .
- Refer to CHECKING THE INTERMEDIATE LEVER CLASSIFICATION .
- Refer to INSTALLING INTERMEDIATE LEVER ON INTAKE SIDE .
- Refer to INSTALLING INTAKE CAMSHAFT OF BANK 1 .
- Refer to INSTALLING SLIDING BLOCKS OF BANK 1 .
- Refer to INSTALLING TORSION SPRINGS .
- Refer to REMOVING THE CYLINDER HEAD OF CYLINDER BANK 1 FROM THE ASSEMBLY JIG .
- Refer to INSTALLING VALVETRONIC SERVOMOTOR, RIGHT (CYLINDER HEAD REMOVED) .
- Refer to INSTALLING RIGHT INTAKE PLENUM (CYLINDER HEAD REMOVED) .
- Refer to INSTALLING RIGHT CYLINDER HEAD .
- Refer to INSTALLING BOTH VANOS ADJUSTERS (CYLINDER HEAD DISASSEMBLY, BANK 1) .
- Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
- Refer to INSTALLING ELECTRIC COOLANT PUMP WITH HOLDER .
- Refer to INSTALLING THE CYLINDER HEAD COVER ON THE RIGHT .
- Refer to INSTALLING THE VACUUM PUMP .
- Refer to INSTALLING HEAT SHIELD ON THE BOTTOM .
- Refer to INSTALLING FRONT HEAT SHIELD .
- Refer to INSTALLING BOTH EXHAUST MANIFOLDS .
- Refer to INSTALLING THE HEAT SHIELD OF THE CYLINDER HEAD COVER FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE HEAT SHIELD OF THE CYLINDER HEAD COVER FOR CYLINDERS 1 TO 4 .
- Refer to INSTALLING LEFT AND RIGHT EXHAUST TURBOCHARGERS .
- Refer to MOUNTING FIXTURE ON THE RIGHT .
- Refer to INSTALLING LEFT MOUNT .
- Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
- Refer to INSTALLING CLEAN AIR PIPE OF CYLINDER BANK 1 .
- Refer to INSTALLING CATALYTIC CONVERTER NEAR THE ENGINE ABOVE CYLINDER BANK 1 .
- Refer to INSTALLING UPPER CATALYTIC CONVERTER NEAR ENGINE FOR BANK 2 .
- Refer to INSTALLING HEAT SHIELD, TOP .
- Installing conduit on bank 2
- Clip the wiring harness (2) into the clamps (1).
- Refer to INSTALLING ENGINE VENTILATION LINE OF CYLINDER BANK 1 .
- Refer to INSTALLING THE HOLDER WITH THE VEHICLE WIRING HARNESS FOR THE SENSOR SYSTEM OF CYLINDER BANK 1 .
- Refer to INSTALLING THE TANK VENTILATION LINE OF CYLINDER BANK 1 PARTIALLY .
- Installing cable duct at cylinder bank 1.
- Position the conduit (2).
- Tighten the screws (1).
TIGHTENING TORQUESCable duct M6x16 screw Tightening torque 10Nm - Refer to INSTALLING THE OXYGEN SENSOR MONITOR OF CYLINDER BANK 1 .
- Refer to INSTALLING THE OXYGEN SENSOR MONITOR OF CYLINDER BANK 2 .
- Refer to CHECKING THE POSITION OF THE HEAT SHIELD .
- Refer to INSTALLING THE EXPANSION TANK FOR THE CHARGE AIR COOLER .
- Refer to INSTALLING COOLANT EXPANSION TANK .
- Refer to INSTALLING HOLDER OF THE DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR THE CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR THE CYLINDERS 1 TO 4 .
- Refer to INSTALLING ALTERNATOR .
- Refer to INSTALLING ELECTRIC COOLANT PUMP WITH HOLDER .
- Refer to INSTALLING FUEL DELIVERY LINE .
- Installing holder with the wiring harness for the sensor system of cylinder bank 2.
- Refer to INSTALLING THE HOLDER WITH THE VEHICLE WIRING HARNESS FOR THE SENSOR SYSTEM OF CYLINDER BANK 1 .
- Refer to INSTALLING THE RIGHT TANK VENT VALVE .
- Refer to INSTALLING THE CHARGE AIR COOLER ON THE LEFT AND RIGHT .
- Refer to CLOSING THE COOLANT PUMPS .
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to INSTALLING DRIVE BELT .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING THE FRONT RIGHT WHEEL .
- Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
- Refer to INSTALLING FAN COWL WITH ELECTRIC MOTOR .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
- Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
- Refer to INSTALLING FRONT CROSS CONNECTION .
- Refer to TIGHTENING THE LEFT FRONT-END STRUT .
- Refer to TIGHTENING THE FRONT-END STRUT ON THE RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE LEFT .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Installing the rear right engine compartment cover.
Remove the battery cover .
NOTE: The following step(s) must be performed if the listed component(s) is/are installed.- Remove the special tool 2 452 007 from the battery.
- Install the cover (2).
- Lock the lock (1).
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .
- Refer to INSTALLING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
- Refer to CHECKING ENGINE OIL LEVEL .