Remove timing case cover, bottom
WARNING: This page is about a different car, the 2023 BMW X5, 2022 BMW X5, 2021 BMW X5, 2020 BMW X5, and 2019 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
Working on fuel system
.
Risk of fire! Danger of explosion!
Risk of fire! Danger of explosion!
- When working on the fuel system, make sure the workstation has sufficient ventilation, e.g., by means of extraction.
- Tightly seal off open lines and connections; collect any leakage fuel directly at the point of exit.
- No fire, sparks, open flames or smoking.
NOTE:
TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.
Preliminary work
- Refer to RELEASING THE OIL DRAIN PLUG .
- Refer to REMOVING THE OIL FILTER ELEMENT .
- Refer to REMOVING THE FRONT AXLE COMPLETELY WITH THE ENGINE AND TRANSMISSION .
- Refer to INSTALLING THE ENGINE ON THE ASSEMBLY JIG .
- Refer to REMOVING FLYWHEEL .
- Refer to REMOVING DRIVE BELT .
- Refer to REMOVING THE BELT TENSIONER .
- Refer to REMOVING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
- Refer to REMOVING THE AIR CONDITIONING COMPRESSOR (ENGINE REMOVED) .
- Refer to REMOVING THE COOLANT PUMP .
- Refer to RELEASING LEFT CHARGE AIR LINE PARTIALLY .
- Refer to PARTIALLY RELEASING THE RIGHT CHARGE AIR LINE .
- Refer to REMOVING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to REMOVING BOTH CHARGE AIR COOLERS .
- Refer to REMOVING RIGHT CLEAN AIR PIPE .
- Refer to REMOVING LEFT CLEAN AIR PIPE .
- Refer to REMOVING ALL IGNITION COILS .
- Refer to REMOVING FUEL DELIVERY LINE .
- Refer to REMOVING RIGHT HIGH-PRESSURE PUMP .
- Refer to REMOVING LEFT HIGH PRESSURE PUMP .
- Refer to PARTIALLY UNDOING WIRING HARNESS FROM RIGHT CYLINDER HEAD COVER .
- Refer to RELEASING THE WIRING HARNESS SECTION FROM THE LEFT HAND CYLINDER HEAD COVER .
- Refer to REMOVING RIGHT RAIL .
- Refer to REMOVING THE HIGH-PRESSURE RAIL ON THE LEFT .
- Refer to REMOVING THE INJECTORS FOR CYLINDERS 1 TO 4 .
- Refer to REMOVING THE INJECTORS FOR CYLINDERS 5 TO 8 .
- REMOVING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 1
- Refer to REMOVE THE VANOS SOLENOID ACTUATOR INTAKE OF CYLINDER BANK 1 .
- REMOVING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 2 .
- Refer to REMOVING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
- Refer to REMOVING THE LEFT AND RIGHT EXHAUST TURBOCHARGER .
- Refer to REMOVING FRONT HEAT SHIELD .
- Refer to REMOVING THE OIL FEED LINE AT THE EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8 .
- Refer to REMOVING RIGHT CYLINDER HEAD COVER .
- Refer to REMOVING LEFT CYLINDER HEAD COVER .
- Refer to REMOVING THE SEALING CAP ON THE CYLINDER HEAD OF THE CYLINDER BANK 2 .
- Refer to REMOVE THE SEALING CAP ON THE CYLINDER HEAD OF THE CYLINDER BANK 1 .
- Refer to MOVING THE CRANKSHAFT TO THE INSTALLATION POSITION TO ADJUST THE TIMINGS .
- Refer to CHECK THE VANOS ADJUSTER OF CYLINDER BANK 2 .
- Refer to RELAXING CHAIN TENSIONER ON BANK 2 FOR CHECKING OR SETTING TIMING .
- Refer to REMOVING HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
- Refer to PRELOADING THE TIMING CHAIN OF CYLINDER BANK 2 .
- Refer to FIXING THE ENGINE IN THE INSTALLATION POSITION ON CYLINDER 1 (SET VALVE TIMINGS) .
- Refer to REMOVING BOTH LEFT VANOS ADJUSTERS .
- Refer to REMOVING SPECIAL TOOL FOR FIXING CAMSHAFTS IN POSITION ON BANK 2 .
- Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
- Refer to REMOVING LEFT CYLINDER HEAD .
- Refer to PARTIALLY RELEASING THE GUIDE TUBE FOR THE OIL DIPSTICK .
- Refer to CHECKING THE VANOS ADJUSTER OF CYLINDER BANK 1 .
- Refer to RELIEVING THE CHAIN TENSIONER AT CYLINDER BANK 1 FOR CHECKING OR SETTING THE VALVE TIMINGS .
- Refer to REMOVING HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 1 .
- Refer to PRELOADING THE TIMING CHAIN OF CYLINDER BANK 1 .
- Refer to FIXING THE ENGINE IN THE INSTALLATION POSITION ON CYLINDER 1 (SET VALVE TIMINGS) .
- Refer to REMOVING BOTH RIGHT VANOS ADJUSTERS .
- Refer to REMOVING SPECIAL TOOL FOR FIXING CAMSHAFTS ON BANK 1 .
- Refer to REMOVING THE SPECIAL TOOL TO PRETENSION THE TIMING CHAIN AT CYLINDER BANK 1 .
- Refer to REMOVING RIGHT CYLINDER HEAD .
- Refer to REMOVING LOWER OIL PAN SECTION .
- Refer to REMOVING OIL PUMP .
- Refer to REMOVING FRONT AXLE DIFFERENTIAL .
- Refer to REMOVING UPPER OIL SUMP SECTION, ENGINE REMOVED .
- Refer to REMOVING THE VIBRATION DAMPER .
- Unlock and disconnect the plug connection (1) on the coolant temperature sensor (2).
Unscrew the screw connection 1 on the timing case cover in front
- Loosen screws in the order (10) to (12).
- Remove the carrier plate (1).
Release the screw connection 2 on the front timing case cover
- Loosen screws in the order (9) to (3).
Release the screw connection 3 on the timing case cover in front
- Loosen screws in the order (1) to (2).
- Remove timing case cover.