Install the oil vacuum pump
- Guide out and remove centering sleeves (1) from the crankcase in the arrow direction using standard tools (2) .
- Replace the centering sleeves (1)
.
Parts: Centering sleeves
- Insert and install centering sleeves (1)
on the oil vacuum pump (2)
.
- Position sprocket wheel (1)
on oil vacuum pump (2)
.
The labeling on the sprocket wheel (1) must point away from the oil vacuum pump (2) .
- Replace the screw (1) .
Parts: Screw
NOTE:
TECHNICAL INFORMATION
The thread is a left-hand thread.
The thread is a left-hand thread.
- Guide in and fix the screw (1) .
NOTE:
TECHNICAL INFORMATION
Conduct the following operation with the assistance of a second person.
Conduct the following operation with the assistance of a second person.
- Grip the sprocket wheel using special tool 0 491 440 (23 0 020) and tighten screw (1) using standard tools (2) .
TIGHTENING TORQUE SPECIFICATION
| Sprocket wheel at the oil vacuum pump | ||
|---|---|---|
| M8 Important - left-hand thread Replace screw. |
1. Joining torque | 5 Nm |
| 2. Angle of rotation | 90° | |
- Guide oil vacuum pump (1)
into drive chain (2)
and position it.
- Replace screws (1)
.
Parts: Screws
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATION
| Oil vacuum pump to crankcase | ||
|---|---|---|
| M8 Replace screw. |
1. Joining torque | 15 Nm |
| 2. Angle of rotation | 45° | |
Follow-up work
- Refer to REFITTING SUMP .
- Refer to INSTALLING STARTER MOTOR .
- Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
- Refer to INSTALLING THE FRONT AXLE SUPPORT .
- Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE PARKED-CAR HEATING .
- Refer to ATTACHING THE LEFT AND RIGHT TENSIONING STRUTS ON THE SWIVEL BEARING .
- Refer to ATTACHING THE LEFT AND RIGHT WISHBONE ON THE SWIVEL BEARING .
- Refer to SECURING THE TIE ROD ON THE LEFT AND RIGHT OF THE SWIVEL BEARING .
- Refer to ATTACHING THE ANTI-ROLL BAR LINK ON THE ANTI-ROLL BAR AT LEFT AND RIGHT .
- Refer to ATTACHING THE LINE CONNECTION TO THE RIDE HEIGHT SENSOR .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
- Refer to REMOVING THE ENGINE FROM THE INSTALLATION POSITION .
- Refer to FILLING ENGINE OIL .
- Refer to OPENING THE OIL FILLER CAP .
- Refer to FASTENING THE WIRING HARNESS SECTION TO THE LEFT SHOCK TOWER .
- Refer to FASTENING THE WIRING HARNESS SECTION TO THE RIGHT SHOCK TOWER .
- Refer to INSTALLING THE SEALING ON LEFT AND RIGHT SIDE PANEL .
- Refer to INSTALLING THE LATERAL HOOD SEALS .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING THE RIGHT FRONT-END STRUT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE LEFT AND RIGHT CRASH LEVER .
- Refer to PARTIALLY INSTALLING THE AIR DUCT FOR THE BRAKE ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE LOWER WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING THE TORSION STRUT LEFT AND RIGHT .
- Refer to INSTALLING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to RECONNECTING ALL BATTERY GROUND LEADS .
- Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to CHECKING ENGINE OIL LEVEL .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .