Installing the acoustic cover for the oil sump

• Insert and position the acoustic cover (1)  of the oil pan.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .
• Replace the fir tree clip (2)  .

  Parts:  Fir tree clip

• Secure the fir tree clip (2)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Position the transmission oil lines (1)  on the bracket (2)  .

Make sure that the marks (3)  have been positioned correctly on the holder (2)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install the holder (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (1)  .

Holder for transmission oil line
Screw	Tightening torque	4 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the connector (1)  .
• Make sure the connector (1)  engages audibly.
• Insert and install the positive battery cable (3)  .
• Secure positive battery cable (3)  at the clamp (4)  .
• Tighten the nut (2)  hand-tight.

Courtesy of BMW OF NORTH AMERICA, INC.

• Attach the positive battery cable (1) correctly  to anti-twist lock (2)  .
• Tighten nut (3)  .

Courtesy of BMW OF NORTH AMERICA, INC.

Battery positive lead to starter
M8	Tightening torque	13.5 Nm

Follow-up work 

• Refer to RAISING THE FRONT SUBFRAME .
• Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE PARKED-CAR HEATING .
• Refer to ATTACHING THE ANTI-ROLL BAR LINK ON THE ANTI-ROLL BAR AT LEFT AND RIGHT .
• Refer to ATTACHING THE LINE CONNECTION TO THE RIDE HEIGHT SENSOR .
• Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
• Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
• Refer to REMOVING THE ENGINE FROM THE INSTALLATION POSITION .
• Refer to FASTENING THE WIRING HARNESS SECTION TO THE LEFT SHOCK TOWER .
• Refer to FASTENING THE WIRING HARNESS SECTION TO THE RIGHT SHOCK TOWER .
• Refer to INSTALLING THE SIDE PANEL SEAL .
• Refer to INSTALLING THE LATERAL HOOD SEALS .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING THE RIGHT FRONT-END STRUT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING THE LEFT AND RIGHT CRASH LEVER .
• Refer to PARTIALLY INSTALLING THE AIR DUCT FOR THE BRAKE ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE LOWER WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
• Refer to INSTALLING THE STIFFENING PLATE .
• Installing the torsion strut left and right
  NOTE: Perform the steps on the right and left side.

  Remove torsion strut 

  IMPORTANT: Driving without torsion strut is prohibited.
  IMPORTANT: Secure component against falling.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .