Tighten the screws on the left and right front axle support
- Replace screws (1)
.
Parts: Screws
- Tighten down screws (1)
.TIGHTENING TORQUES SPECIFICATION
Front axle carrier to body, front M12
Replace screws.Joining torque 108 Nm Angle of rotation 45° - Replace screws (2)
.
Parts: Screws
- Tighten down screws (2)
.TIGHTENING TORQUES SPECIFICATION
Front axle support to center of body M12
Replace screws.Joining torque 108 Nm Angle of rotation 45° - Replace screws (3)
.
Parts: Screws
- Tighten down screws (3)
.TIGHTENING TORQUES SPECIFICATION
Front axle carrier to body, rear M14
Replace screws.Joining torque 108 Nm Angle of rotation 45° NOTE: Perform the steps on the right and left side. - Replace screws (1)
.
Parts: Screws
- Tighten down screws (1)
.TIGHTENING TORQUES SPECIFICATION
Bottom bumper bracket on the front subframe . M8x100
Replace screws.Tightening torque 19 Nm
Follow-up work
- Refer to SECURING THE WISHBONE ON THE TOP LEFT AND RIGHT ON THE SWIVEL BEARING .
- Refer to REMOVING THE MOBILE LIFTING TABLE .
- Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
- Refer to IF INSTALLED: SECURING THE LINE FOR THE VERTICAL ACCELERATION SENSOR ON THE RIGHT AND LEFT .
- Refer to ATTACHING THE CABLE OF THE WHEEL RPM SENSOR ON THE LEFT AND RIGHT .
- Refer to SECURING THE FRONT LEFT AND RIGHT BRAKE CALIPER .
- Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
- Refer to INSTALLING THE LEFT-HAND AND RIGHT-HAND CRASH LEVER .
- Refer to ATTACHING THE LEFT AND RIGHT SPRING STRUT ON THE WISHBONE ON THE BOTTOM .
- Refer to IF INSTALLED: INSTALLING THE SILENCER/STATIONARY HEATING (ADDITIONAL STEPS, PROCESS NUMBER: 31 11 905) .
- Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
- Refer to ATTACHING THE UNIVERSAL JOINT TO STEERING GEAR .
- Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING THE TORSION STRUT LEFT AND RIGHT .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to FASTENING THE FRONT LEFT AND RIGHT SPRING STRUT .
- Refer to INSTALLING THE SIDE HOOD SEAL ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
- Refer to INSTALLING CLEAN AIR PIPE, TOP .
- Refer to INSTALLING INTAKE SILENCER HOUSING .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to PLACING THE BRAKE PADS ON THE BRAKE DISK/PUTTING THEM INTO OPERATION .
- Refer to MEASURING THE RIDE HEIGHT OF THE FRONT AXLE AND ADJUSTING THE NORMAL POSITION .
- Refer to TIGHTENING THE SCREW CONNECTION ON THE LEFT AND RIGHT WISHBONE IN THE NORMAL POSITION .