Remove the special tools to disconnect the crankshaft

• Remove special tool 0 493 882 (11 9 190) (1)  .
• Release the screw (2)  of the belt pulley.
• Remove special tool 0 496 366 (11 8 570) (3)  .

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• INSTALLING THE SEALING CAP ON THE CYLINDER HEAD OF CYLINDER BANK 1 .
• INSTALLING THE PRESSURE LINE BETWEEN THE EVAPORATOR AND AIR CONDITIONING CONDENSER .
• INSTALLING THE LEFT CYLINDER HEAD COVER .
• INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
• INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2 .
• INSTALLING THE LEFT HIGH PRESSURE PUMP .
• INSTALLING FUEL DELIVERY LINE .
• INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
• INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
• INSTALLING THE IGNITION COILS OF CYLINDER BANK 2 .
• INSTALLING THE IGNITION COILS OF CYLINDERS 1 AND 5 .
• INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
• INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
• INSTALLING CLEAN AIR PIPE OF CYLINDER BANK 1 .
• INSTALLING BOTH CHARGE AIR COOLERS .
• CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• CLOSING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
• INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT (CHARGE AIR COOLER) .
• SEALING OFF COOLANT FOR LOW-TEMPERATURE COOLANT CIRCUIT .
• INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
• INSTALLING FRONT UNDERBODY PROTECTION .
• INSTALLING THE BOTTOM FRONT RIGHT SIDE COVER .
• INSTALLING DRIVE BELT .
• INSTALLING FAN COWL .
• INSTALLING THE REAR TOP CROSS CONNECTION .
• INSTALLING UPPER CROSS CONNECTION .
• INSTALLING BOTH FRONT-END STRUTS .
• INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
• INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 5 TO 8 .
• RELEASING THE HEAT SHIELD .
• INSTALLING THE CENTER COWL UPPER PART .
• INSTALLING TENSION STRUT ON SHOCK TOWER .
• ATTACHING WINDSHIELD PANEL COVER .
• INSTALLING LEFT AND RIGHT WIPER ARM .
• INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• INSTALLING RIGHT HEAT SHIELD .
• INSTALLING LEFT HEAT SHIELD .
• INSTALLING HEAT SHIELD, TOP .
• INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
• INSTALLING THE LEFT OXYGEN SENSOR MONITOR .
• PARTIALLY INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
• PARTIALLY INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
• INSTALLING THE RETAINING BRIDGE IN VEHICLES WITH A GASOLINE PARTICULATE FILTER .
• INSTALLING THE RETAINING BRIDGE .
• INSTALLING EXHAUST SYSTEM .
• INSTALLING CENTER STIFFENING PLATE .
• INSTALLING TANK COVER ON LEFT AND RIGHT .
• INSTALLING REAR PANEL .
• PARTIALLY INSTALLING THE REAR LEFT AND RIGHT WHEEL ARCH COVERS .
• INSTALLING BOTH EXHAUST COVERS .
• INSTALLING BOTH SIDE REAR TRIM STRIPS .
• INSTALLING THE REAR BUMPER TRIM .
• INSTALLING THE REAR DIFFUSER .
• INSTALLING THE TAIL LIGHT ON THE LEFT AND RIGHT SIDE PANELS .
• INSTALLING COVER FOR WATER CHANNEL ON LEFT AND RIGHT .
• INSTALLING THE LUGGAGE COMPARTMENT WHEEL ARCH TRIM PANEL ON THE LEFT AND RIGHT (PARTIALLY REMOVED) .
• INSTALLING BOTH LEDs IN THE CARGO AREA .
• INSTALLING LOADING EDGE TRIM .
• INSTALLING LUGGAGE COMPARTMENT FLOOR COVERING .