Install oil pump
- Feed out the centering sleeves (1) from the crankcase in the arrow direction with standard tools (2) and remove it.
- Replace the centering sleeves (1)
.
Parts: Centering sleeves
- Insert and install new centering sleeves (1)
on the oil pump (2)
.
- Position the sprocket wheel (1)
on the oil pump (2)
.
The labeling on the sprocket (1) must point away from the oil pump (2) .
- Replace screw (1).
Parts: Screw
NOTE: TECHNICAL INFORMATION
The thread is a left-hand thread. - Guide in and fix the screw (1)
.NOTE: TECHNICAL INFORMATION
Conduct the following operation with the assistance of a second person. - Counter support the sprocket with the special tool 0 491 440 (23 0 020) and tighten the screw (1) with
standard tools (2)
.TIGHTENING TORQUE SPECIFICATIONS
Sprocket to oil pump M8
Important - left-hand thread
Replace screw.1. Joining torque 5 Nm 2. Angle of rotation 90° - Feed the oil pump (1) into the drive chain (2)
and position it,
- Replace the screws (1)
.
Parts: Screws
- Tighten down screws (1).TIGHTENING TORQUE SPECIFICATIONS
Oil pump to crankcase M8
Replace screw.1. Joining torque 15 Nm 2. Angle of rotation 45°
Follow-up work
- Refer to REFITTING OIL PAN .
- Refer to INSTALLING STARTER MOTOR .
- Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
- Refer to INSTALLING BEARING BRACKET .
- Refer to INSTALLING FRONT AXLE DIFFERENTIAL .
- Refer to SECURING THE JUNCTURE SHAFT IN FRONT ON THE FRONT AXLE DIFFERENTIAL .
- Refer to REPLACING THE LEFT AND RIGHT RADIAL SHAFT SEAL RING .
- Refer to INSTALLING FRONT AXLE COMPLETELY .
- Refer to TIGHTENING THE BOLTS ON THE FRONT AXLE SUPPORT .
- Refer to SECURING THE SWIVEL BEARING AT THE TOP LEFT AND RIGHT .
- Refer to REMOVING THE MOBILE LIFTING TABLE .
- Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
- Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
- Refer to IF INSTALLED: SECURING THE LINE FOR THE VERTICAL ACCELERATION SENSOR ON THE RIGHT AND LEFT .
- Refer to ATTACHING THE CABLE OF THE WHEEL RPM SENSOR ON THE LEFT AND RIGHT .
- Refer to SECURING THE FRONT LEFT AND RIGHT BRAKE CALIPER .
- Refer to INSTALLING THE LEFT-HAND AND RIGHT-HAND CRASH LEVER .
- Refer to IF INSTALLED: INSTALLING THE SILENCER/STATIONARY HEATING (ADDITIONAL STEPS, PROCESS NUMBER: 31 11 905) .
- Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to INSTALLING THE OUTPUT SHAFT ON LEFT AND RIGHT .
- Refer to CHECK/ADD FRONT AXLE TRANSMISSION OIL .
- Refer to INSTALLING THE LEFT AND RIGHT SPRING STRUT HOLDER .
- Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
- Refer to ATTACHING THE UNIVERSAL JOINT TO STEERING GEAR .
- Refer to INSTALLING THE RIGHT REINFORCEMENT STRUT .
- Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE TORSION STRUT LEFT AND RIGHT .
- Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to INSTALLING FUEL DELIVERY LINE .
- Refer to INSTALLING ALL IGNITION COILS .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to ATTACHING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to FASTENING THE FRONT LEFT AND RIGHT SPRING STRUT .
- Refer to INSTALLING THE SIDE HOOD SEAL ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
- Refer to INSTALLING CLEAN AIR PIPE, TOP .
- Refer to INSTALLING INTAKE SILENCER HOUSING .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to PLACING THE BRAKE PADS ON THE BRAKE DISK/PUTTING THEM INTO OPERATION .
- Refer to TIGHTENING THE SCREW CONNECTION ON THE SPRING STRUT HOLDER IN THE NORMAL POSITION .