Installing the left-hand charge air cooler

• Replace hose (1)  .

  Parts:  Hose

• Position hose (1)  with hose clamps (2)  as shown.
• Replace hose (5)  .

  Parts:  Hose

• Position the hose (5)  and the hose clamp (3)  (diameter 60-80 mm) at the top.
• Ensure that the hose clamp at the top (3)  in the area of threaded connection is aligned with the screw on boost pressure sensor.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position hose clamp (4)  on hose (5)  (diameter of 77-84 mm) at the bottom.
• Ensure that the hose clamp at the bottom (4)  in the area of the threaded connection is aligned with the rubber mount on the charge air cooler.
• Guide in and position charge air cooler (2) at the bottom  .
• Tighten hose clamp (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Position the connecting plate (2)  between the charge air coolers.
• Tighten down screws (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Connect hose (2)  .

  The retaining clip (1)  must snap-in audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Engage the holder (2)  on the charge air cooler.
• Tighten down screw (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Connect the line (1)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the holder (3)  in the groove (4)  .
• Tighten down screw (2)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness mounting (1)  .
• Tighten hose clamp (1)  .

• Tighten hose clamp (2)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Slide the hose (2)  onto the studs of the charge air cooler.
• Replace the hose clamps (3)  and the hose.

  Parts:  Hose clamps and hose

• Fasten the hose clamps (3)  .
• Thread in the hose (1)  in the holder on the charge air cooler (4)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Slide the hose (2)  onto the studs of the charge air cooler.
• Replace the hose clamps and the hose.

  Parts:  Hose clamps and hose

• Fasten the hose clamps (3)  .
• Feed the hose (1)  into the holder on the charge air cooler (4)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach the coolant lines (2)  .

  The retaining clips (1)  must snap-in audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the cable in the cable bracket (2)  .
• Lock the cable bracket (2)  .
• Connect connectors (1)  and lock.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to CLOSING THE COOLANT PUMPS .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
• Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
• Refer to INSTALLING FAN COWL WITH ELECTRIC MOTOR .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
• Refer to TIGHTENING THE FRONT-END STRUT ON THE RIGHT .
• Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
• Refer to TIGHTENING THE LEFT FRONT-END STRUT .
• Refer to INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE FRONT HOOD SEAL .
• Refer to INSTALLING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
• Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .