Rear Final Drive 0BC, 0BD, 0BE & 0BF

• 39 Final Drive, Differential
  • General Information
    • ATF, Draining And Filling
      • ATF, Draining, 0BE
      • ATF, Draining, 0BF
      • ATF, Filling, 0BE, 0BF
    • Gear Oil, Checking Level
      • Gear Oil, Checking Level, 0BC
      • Gear Oil, Checking Level, 0BE, 0BF
    • Gear Oil, Draining, 0BE, 0BF
    • Gear Oil, Filling, 0BE
    • Gear Oil, Filling, 0BF
  • Description And Operation
    • Driveshaft, Bolts On Transmission Side Overview
    • Driveshaft, Mounted On Transmission Side Overview
    • Final Drive 0BC, 0BD Overview
      • Notes
      • Balance Weight on the Rear Final Drive
    • Final Drive 0BE, 0BF Overview
    • Gear Oil Drain And Inspection Plugs Overview, 0BE
    • Gear Oil Drain And Inspection Plugs Overview, 0BF
    • Gear Oil Drain And Inspection Plugs Overview, 0BE, 0BF
    • Seals Component Location Overview, 0BC, 0BD
    • Seals Component Location Overview, 0BE, 0BF
    • Transmission Control Component Location Overview
  • Specifications
    • Fastener Tightening Specifications
  • Diagnosis And Testing
    • Torque Development, Checking, 0BE, 0BF
    • ATF Level, Checking, 0BE, 0BF
  • Removal And Installation
    • AWD Control Module -J492-
    • All Wheel Drive Clutch Valve -N445- Or All Wheel Drive Clutch Valve 2 -N446-, 0BE, 0BF
      • Notes
      • Removing
      • Installing
    • All Wheel Drive Pump -V415-, 0BE, 0BF
      • Notes
      • Removing
      • Installing
    • Additional Work After Replacing All Wheel Drive Control Module -J492-
    • Boot, Replacing, Driveshaft Connected On Transmission Side
    • Driveshaft, Driveshaft Connected On Transmission Side
      • Notes
      • Removing
      • Installing
    • Driveshaft, Driveshaft Bolted On Transmission Side
    • Driveshaft, Bolts On Transmission Side
    • Driveshaft, Removing From Rear Final Drive And Installing
      • Notes
      • Install Driveshaft on Rear Final Drive.
    • Final Drive
      • Final Drive 0BC
        • Notes
        • Removing
        • Installing
      • Final Drive 0BE, 0BF
        • Notes
        • Removing
        • Installing
      • Additional Work After Replacing Rear Final Drive 0BE, 0BF
        • Notes
        • Tightening Specification
    • Flange Input Shaft Ring, Replacing
      • Flange Input Shaft Ring, Replacing, 0BC
      • Flange Input Shaft Ring, Replacing, 0BE, 0BF
    • Flange Shaft Protective Ring, Replacing
      • Flange Shaft Ring, Replacing, 0BC
      • Flange Shaft Ring, Replacing, 0BE, 0BF
    • Hydraulic Control Module, 0BE, 0BF
      • Notes
      • Removing
        • Notes
        • If equipped, remove the bolts -arrows- and remove the wiring harness bracket -1- from the rear final drive.
        • Loosen the left -6- and right -7- lines to the hydraulic control unit -1- one turn -arrows A- and remove them from the chambers -arrows B-.
      • Installing
        • Notes
        • Attach the hydraulic control unit -1- to the rear final drive as follows:
    • Oil Pressure/Temperature Sensor -G437- OR Oil Pressure/Temperature Sensor 2 -G640-, 0BE, 0BF
      • Notes
      • Removing
      • Installing
    • Left Seal, Replacing
      • Left Seal, Replacing, 0BC
        • Notes
        • Removing
        • Installing
      • Left Seal, Replacing, 0BE, 0BF
        • Notes
        • Removing
        • Installing
    • Input Shaft Seal, Replacing
      • Input Shaft Seal, Replacing, 0BC
        • Notes
        • Removing
        • Installing
      • Input Shaft Seal, Replacing, 0BE
        • Notes
        • Removing
        • Installing
      • Input Shaft Seal, Replacing, 0BF
        • Notes
        • Removing
        • Installing
  • Disassembly And Assembly
    • Notes
    • Hydraulic Control Unit, 0BE, 0BF
  • Special Tools