| Driveshaft to rear final drive - tightening specification and sequence |
- |
Refer to Figure |
| Driveshaft heat shield - tightening specification |
- |
Refer to Figure |
| Intermediate bearing bolt |
- |
20 |
| Lock plate to driveshaft 1 |
- |
30 + 90° |
| Final Drive 0BC, 0BD |
| Balance weight to rear final drive bolt 3 |
- |
22 |
| Balance weight to rear final drive bolt 4 |
- |
55 |
| Crossmember to rear final drive bolt |
- |
55 |
| Heat shield to crossmember bolt |
- |
20 |
| Subframe 2 |
| - Bolt |
- |
55 |
| - Bolt |
- |
95 |
| Final Drive 0BF Assembly Overview, A4, A5, A6, and A7 |
| Heat shield to rear final drive bolt |
- |
20 |
| Subframe 5 |
| - Bolt |
- |
55 |
| - Bolt |
- |
95 |
| Final Drive 0BF, RS5 |
| Heat shield to rear final drive bolt |
- |
20 |
| Subframe 6 |
| - Bolt |
- |
55 |
| - Bolt |
- |
95 |
| Final Drive 0BE, 0BF A8 |
| Heat shield to rear final drive bolt |
- |
20 |
| Subframe 7 |
| - Bolt |
- |
55 |
| - Bolt |
- |
95 |
| Gear Oil Drain and Inspection Plugs 0BE, 0BF |
| Drain plug for gear oil 1 |
- |
15 |
| Inspection plug for gear oil 1 |
- |
15 |
| Final Drive 0BE, 0BF |
| All Wheel Drive Clutch Valve 2 -N446- to hydraulic control unit housing bolt |
- |
2.5 |
| All Wheel Drive Pump -V415- to hydraulic control unit housing bolt |
- |
5 |
| ATF check plug 1 |
- |
15 |
| ATF drain plug 1 |
- |
15 |
| Bracket for wiring harness to rear final drive bolt |
- |
9 |
| Gear oil drain plug 1 |
- |
15 |
| Gear oil inspection plug 1 |
- |
15 |
| Gear oil checking plug 0BC |
- |
30 |
| Gear oil checking plug 0BD |
- |
45 |
| Hydraulic control unit 9 |
| - Bolt 8 |
M8 x 50 |
20 see tightening sequence Attach the hydraulic control unit -1- to the rear final drive as follows: |
| - Bolt |
M8 x 30 |
| Left line to Hydraulic Control Unit Housing nut |
- |
30 |
| Oil Pressure/Temperature Sensor |
- |
10 |
| Right Flange Shaft to Final Drive bolt 1 |
- |
50 + 90° |
| Right line to Hydraulic Control Unit Housing nut |
- |
30 |
| Shuttle valve |
- |
8 |
| Gear Oil Drain and Inspection Plugs, 0BE, 0BF |
| ATF drain plug 1 |
- |
15 |
| ATF inspection plug 1 |
- |
15 |
| |
- |
|
- 1
Replace
- 2
For bolt tightening clarification, refer to FINAL DRIVE 0BC, 0BD OVERVIEW and see items -2 and 3-
- 3
For bolt tightening clarification, refer to FINAL DRIVE 0BC, 0BD OVERVIEW and see items -1-
- 4
For bolt tightening clarification, refer to FINAL DRIVE 0BC, 0BD OVERVIEW and see items -9-
- 5
For bolt tightening clarification, refer to FINAL DRIVE 0BC, 0BD OVERVIEW
and see items -2 and 3-
- 6
For bolt tightening clarification, refer to FINAL DRIVE 0BC, 0BD OVERVIEW
and see items -1 and 8-
- 7
For bolt tightening clarification, refer to FINAL DRIVE 0BE, 0BF OVERVIEW and see items -1 and 8-
- 8
Coat the thread with Sealing Compound D 176 501 A1
- 9
For bolt tightening clarification, refer to FINAL DRIVE 0BE, 0BF OVERVIEW and see items -7, 8 and 9-
|