Input Shaft Seal, Replacing, 0BC: Removing

Fig 1: Identifying Exhaust System Clamping Sleeves

Courtesy of AUDI OF AMERICA, LLC

Rear final drive installed
General repair instructions, refer to REPAIR INFORMATION .

-- Disconnect the exhaust system at the clamping sleeves -1- and -2-.

-- Remove the rear section of the exhaust system. Refer to ENGINES CPNA - OVERVIEW - MUFFLER , ENGINES CTUB - MUFFLER OVERVIEW , ENGINES CEUA, CGTA, CTFA & CTFA - OVERVIEW - MUFFLER ENGINES CDRA - EXHAUST PIPES/MUFFLERS, SEPARATING or ENGINES CEJA & CTNA - OVERVIEW - MUFFLER .

NOTE:

A second technician is needed to help remove the rear section of the exhaust system.

-- Open the transmission fluid drain plug -arrow- and allow approximately 250 ml of gear oil to drain out.

Fig 2: Opening Gear Oil Drain Plug And Let Approximately 250 Ml Gear Oil Drain Out

Courtesy of AUDI OF AMERICA, LLC

-- Install the drain plug -arrow- and tighten it.

Tightening specification: 30 Nm

-- Remove the driveshaft from the rear final drive. Refer to DRIVESHAFT, REMOVING FROM REAR FINAL DRIVE AND INSTALLING .

Fig 3: Identifying Mark Position Of Driveshaft Flange To Rear Final Drive

Courtesy of AUDI OF AMERICA, LLC

Audi A8

-- Guide the driveshaft between the fuel tank and the subframe downward toward the rear and attach it on the side.

Audi A4, A5 Coupe/Sportback/Cabrio, Q5

Fig 4: Identifying Crossmember

Courtesy of AUDI OF AMERICA, LLC

-- Remove the front crossmember -2-.

-- Remove the rear crossmember -3- and the heat shield -1-.

Audi A6 and A7

Fig 5: Identifying Crossbrace

Courtesy of AUDI OF AMERICA, LLC

-- Remove the crossmember -2-. Refer to OVERVIEW - UNDERBODY PANELS .

Continuation for All Vehicles - Except Audi A8

-- Remove the bolts -arrows- for the driveshaft intermediate bearing.

Fig 6: Identifying Mounting Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Lower the driveshaft at the center bearing.

-- Guide the driveshaft between the fuel tank and the subframe downward and toward the rear while doing this.

-- Install the center bearing bolts -arrows- by hand.

-- Tie the driveshaft to the side.

All Vehicles

Fig 7: Identifying Circlip, Removal/Installation

Courtesy of AUDI OF AMERICA, LLC

-- Remove the High Temperature Grease in the flange/driveshaft.

-- Remove the circlip -arrow-.

CAUTION:

Replace the circlip with a new one of the same thickness if it is stretched or damaged. Allocation .

-- Mark the position of the flange/driveshaft -B- on the pinion -A- -arrow-.

Fig 8: Locating Mark Position Of Flange/Driveshaft To Pinion

Courtesy of AUDI OF AMERICA, LLC

NOTE:

This marking -arrow- is needed so the colored point -C- on the outer flange remains in its original position.

This ensures the imbalance in the rear final drive will be as small as possible.

-- Install the Two M8 x 30 Bolts -arrow- in the flange.

Fig 9: Pulling Off Drive Shaft Flange Using Puller VW 391

Courtesy of AUDI OF AMERICA, LLC

-- Remove the flange/driveshaft using the Puller VW 391.

-- Lay a super absorbent cloth -A- under the final drive on the subframe.

Fig 10: Identifying Cloth Under Final Drive On Subframe

Courtesy of AUDI OF AMERICA, LLC

-- Knock through the metal ledge of the seal -A-, for example, with a scriber -B- -direction of arrow-.

Fig 11: Puncturing Metal Cover Using Scriber

Courtesy of AUDI OF AMERICA, LLC

-- Then install a sheet metal screw -arrow- in this opening -A-.

Fig 12: Identifying Screw On Metal Cover

Courtesy of AUDI OF AMERICA, LLC

-- Remove the flange/driveshaft seal -A- in -direction of arrow-.

Fig 13: Identifying Flange/ Driveshaft Seal, Removal

Courtesy of AUDI OF AMERICA, LLC

-B- sheet metal screw