LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Mirai >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information >> Instrument Panel Safety Pad >> Removal [06/2015 - 01/2018] >> Procedure

Removal [06/2015 - 01/2018]: Procedure

  1. TABLE OF BOLT, SCREW, NUT 

    HINT: 

    • All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.
      GTY573748Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

    Refer to PRECAUTION [06/2015 - ]

  3. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM 

    HINT: 

    If the AUTO-AWAY is not disabled before disconnecting the negative (-) auxiliary battery terminal, the steering column cover will be difficult to remove. So, disable the AUTO-AWAY before disconnecting the negative (-) auxiliary battery terminal.

    Refer to CUSTOMIZE PARAMETERS [06/2015 - ]

  4. REMOVE FRONT SEAT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to REMOVAL [06/2015 - 11/2018]

  5. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Disengage the claws and guide to remove the front door scuff plate LH as shown in the illustration.
      GTY600353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  6. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Disengage the claws and guide to remove the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
      GTY602080Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disconnect the connector and disengage the clamp.
  7. REMOVE COWL SIDE TRIM BOARD LH 
    1. Remove the clip.
      GTY594188Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clip to remove the cowl side trim board LH as shown in the illustration.
      GTY572848Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  8. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  9. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 
    1. As shown in the illustration, use moulding remover A to raise up the No. 1 instrument panel speaker panel sub-assembly.
      GTY579861Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Lift up in the direction shown by the arrow in the illustration to disengage the claws and clips.
    3. Disengage the guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.
      GTY586518Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  10. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 

    HINT: 

    Use the same procedure as for the No. 1 side.

  11. REMOVE NO. 2 FRONT SPEAKER ASSEMBLY 

    Refer to PROCEDURE - Step 2

  12. REMOVE NO. 1 INSTRUMENT PANEL CUSHION 
    1. Remove the 2 screws <H>.
      GTY608287Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a LH Side
      *b RH Side
    2. Remove the 5 clips.
      GTY594195Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the clips and claws to remove the No. 1 instrument panel cushion.
      GTY597773Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
    1. Disconnect the front door opening trim weatherstrip LH.
  14. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  15. REMOVE FRONT PILLAR GARNISH LH 
    1. Disconnect the 2 front pillar garnish clips from the front pillar garnish LH as shown in the illustration.
      GTY545214Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
    2. Using needle-nose pliers with their tips ends wrapped in protective tape, turn the front pillar garnish clip clockwise 90°and remove it from the front pillar garnish LH.
      GTY576021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:
      • If the front pillar garnish clip is not removed from the vehicle and has no damage, the clip can be reused.
      • If the front pillar garnish clip is removed from the vehicle, replace it with a new one.
    3. Disengage the guides to remove the front pillar garnish LH as shown in the illustration.
      GTY583849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    4. Remove the 2 front pillar garnish clips from the body.
    5. Protect the curtain shield airbag:
      1. Cover the airbag with cloth or similar and fasten it with packing tape as shown in the illustration.
        GTY610509Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 CURTAIN SHIELD AIRBAG
        Packing Tape
        NOTE:

        Protect curtain shield airbag as soon as the front pillar garnish LH is removed.

  16. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  17. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Remove the 2 screws <H> or <I>.
      GTY609952Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the claws and guide to remove the No. 1 instrument panel under cover sub-assembly as shown in the illustration.
      GTY550825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    3. Disconnect the connectors and disengage the clamp.
  18. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY 

    Refer to PROCEDURE - Step 1

  19. REMOVE INSTRUMENT CENTER UPPER CLUSTER FINISH PANEL 
    1. Using a moulding remover A, disengage the claws to open the cover.
      GTY594174Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the screw <H> or <I>.
      GTY551232Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claw and clips to remove the instrument center upper cluster finish panel as shown in the illustration.
      GTY557617Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  20. REMOVE INSTRUMENT CENTER PANEL REGISTER ASSEMBLY 
    1. Open the glove compartment door assembly.
    2. Apply protective tape as shown in the illustration.
      GTY564800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    3. Disengage the claws and clips as shown in the illustration.
      GTY563665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
      NOTE:

      The claws (A) in the illustration are 2-stage, so in this step, disengage the end portions.

    4. Disengage the clips and claws in the order shown in the illustration.
      GTY571332Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Lift up in the direction shown by the arrow (1) in the illustration, pull in the direction shown by the arrow (2) in the illustration to disengage the clips, and remove the instrument center panel register assembly.
      GTY577396Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
      NOTE:

      The claws in the illustration are 2-stage, so in this step, disengage the tips.

    6. Disconnect the connector.
  21. REMOVE NAVIGATION RECEIVER ASSEMBLY 

    Refer to PROCEDURE - Step 6

  22. REMOVE LOWER STEERING COLUMN COVER 

    Refer to PROCEDURE - Step 5

  23. REMOVE UPPER STEERING COLUMN COVER 

    Refer to PROCEDURE - Step 6

  24. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Pull in the direction shown by the arrow in the illustration.
      GTY546380Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
    2. Disengage the claws, clips and guides in the order shown in the illustration to remove it.
      GTY554806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the connector.
  25. REMOVE INSTRUMENT SIDE PANEL LH 
    1. Disengage the claws and clips as shown in the illustration.
      GTY560800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the claw, clip and guide as shown in the illustration to remove it.
      GTY604102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  26. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL 
    1. Disengage the claw and guides to remove the hood lock control lever sub-assembly as shown in the illustration.
      GTY582696Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Remove the bolt <C>.
      GTY594173Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claws and clips to remove the instrument panel lower finish panel as shown in the illustration.
      GTY598411Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    4. Disconnect the connectors and disengage the clamp.
  27. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Disengage the clips and claws to remove the No. 2 instrument panel register assembly.
      GTY549359Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  28. REMOVE INSTRUMENT SIDE PANEL RH 

    HINT: 

    Use the same procedure as for the LH side.

  29. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY 
    1. Remove the 2 bolts <C> and 3 screws <H> or <I>.
      GTY556466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the claws and clips to remove the glove compartment door assembly as shown in the illustration.
      GTY606533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
    3. Disconnect the connector.
  30. REMOVE FRONT CONSOLE BOX COVER 

    See step  12

  31. REMOVE CONSOLE COMPARTMENT BOX ASSEMBLY 

    See step  13

  32. REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY 

    Refer to PROCEDURE - Step 2

  33. REMOVE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY 

    Refer to PROCEDURE - Step 3

  34. REMOVE NO. 6 CONSOLE BOX RETAINER 

    See step  16

  35. REMOVE NO. 1 FRONT CONSOLE BOX INSERT 

    See step  17

  36. REMOVE NO. 2 FRONT CONSOLE BOX INSERT 

    HINT: 

    Use the same procedure as for the No. 1 side.

  37. REMOVE NO. 2 CONSOLE BOX DUCT 

    See step  19

  38. REMOVE NO. 1 CONSOLE BOX DUCT 

    See step  20

  39. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY 

    See step  21

  40. REMOVE NO. 4 CONSOLE BOX DUCT 

    See step  22

  41. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY 

    See step  23

  42. REMOVE LOWER INSTRUMENT PANEL ASSEMBLY 
    1. Remove the 2 clips.
      GTY609956Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts <B> and 10 screws <G>.
      GTY609556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the 2 connectors.
      GTY594278Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Lift up in the direction shown by the arrow (1) in the illustration to disengage the guides.
      GTY545215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
    5. Pull in the direction shown by the arrow (2) in the illustration to remove the lower instrument panel assembly.
  43. REMOVE COMBINATION METER ASSEMBLY 

    Refer to PROCEDURE - Step 13

  44. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Remove the 10 bolts <C>, 2 bolts <D> and nut <A>.
      GTY574760Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the slider to disconnect the instrument panel wire.
      GTY581942Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Slider
    3. Disconnect the connectors and disengage the clamps.
    4. Remove the bolt.
      GTY609981Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the guide to disconnect the No. 3 antenna cord sub-assembly.
      GTY594276Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the 4 bolts <D>.
      GTY609980Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the 2 screws <H>.
      GTY594275Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Disengage the guides to disconnect the shift lever with bracket.
    9. To prevent scratches or damage to the parts during removal, place cloth in the location shown in the illustration.
      GTY571245Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cloth
    10. Remove the upper instrument panel sub-assembly:
      GEMPTY001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the upper instrument panel sub-assembly as shown in the illustration.
        GTY577446Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Remove in this Direction (1) Remove in this Direction (2)
        Remove in this Direction (3) - -
scientia non olet · About LEMON Manuals