LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 197 (Interior) >> ROOF HEADLINING (for Sedan) >> Installation

ROOF HEADLINING (for Sedan): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See PRECAUTION ).
NOTE: Always use "Tone" socket wrench E10 when installing the front seat.
Fig 1: Identifying Roof Headlining (1 Of 2)
G04835400Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. INSTALL ROOF HEADLINING ASSEMBLY 
    1. Install the roof headlining into the front door.
      Fig 2: Identifying Roof Headlining (2 Of 2)
      G04835400Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/ Curtain Shield Airbag:
      1. Engage the 4 hooks.
      2. Install the 2 clips.
        Fig 3: Identifying Clips & Hooks (With Curtain Shield Airbag)
        G04835398Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. w/o Curtain Shield Airbag:
      1. Engage the 2 claws and 4 hooks.
      2. Install the 2 clips.
        Fig 4: Identifying Claws & Hooks (Without Curtain Shield Airbag)
        G04835399Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Connect the antenna connector.
    5. Install the clamp.
      Fig 5: Locating Antenna Connector & Clamp
      G04835397Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Connect the roof wire connector.
      Fig 6: Locating Roof Wire Connector
      G04835396Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the 2 clamps.
      Fig 7: Identifying Roof Headlining Assembly Clamps
      G04835395Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL MAP LIGHT ASSEMBLY 
    1. Connect the map light connector.
      Fig 8: Locating Map Light Connector
      G04835394Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the 4 claws and install the map light.
      Fig 9: Identifying Map Light Claws
      G04835408Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL ROOM LIGHT ASSEMBLY 
    1. Engage the 4 claws and install the room light switch base.
    2. Install the roof wire into the claw of the room light.
      Fig 10: Identifying Room Light Switch Base Claws
      G04835409Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Engage the 4 claws and install the room light.
      Fig 11: Identifying Room Light Claws
      G04835410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Engage the 2 claws and install the cover.

      HINT:

      Use the same procedure for both sides.

      Fig 12: Identifying Cover Claws
      G04835411Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Engage the 4 claws and install the room light lens.
      Fig 13: Identifying Room Light Lens Claws
      G04835412Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL VISOR HOLDER RH 
    1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.
  5. INSTALL VISOR HOLDER LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 14: Identifying Visor Holder Angle
    G04835413Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL VISOR ASSEMBLY RH 
    1. Engage the 2 springs and install the visor.
    2. Install the visor shaft into the visor holder.
      Fig 15: Locating Visor Holder & Springs
      G04835387Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Engage the 4 claws and install the visor bracket cover.
  7. INSTALL VISOR ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 16: Identifying Visor Bracket Cover Claws
    G04835415Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL ASSIST GRIP SUB-ASSEMBLY 

    HINT:

    Use the same procedure to install all the assist grips.

    Fig 17: Identifying Assist Grip Sub-Assembly
    G04835384Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Engage the 2 springs and install the assist grip.
      Fig 18: Identifying Assist Grip Springs
      G04835385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSTALL ASSIST GRIP COVER 

    HINT:

    Use the same procedure to install all the assist grip covers.

    Fig 19: Identifying Assist Grip Covers
    G04835382Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Engage the 2 claws and install the assist grip cover.
  10. INSTALL INSTRUMENT PANEL BOX (See  INSTALLATION  ) 
  11. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY (See  INSTALLATION  ) 
  12. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (See  INSTALLATION  ) 
  13. INSTALL COMBINATION METER ASSEMBLY (See  INSTALLATION  ) 
    Fig 20: Identifying Assist Grip Cover Claws
    G04835419Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL INSTRUMENT CLUSTER FINISH PANEL (See  INSTALLATION  ) 
  15. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (See  INSTALLATION  ) 
  16. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (See  INSTALLATION  ) 
  17. INSTALL REAR CONSOLE BOX ASSEMBLY (See  INSTALLATION  ) 
  18. INSTALL REAR CONSOLE BOX CARPET (See  INSTALLATION  ) 
  19. INSTALL REAR CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY (See  INSTALLATION  ) 
  20. INSTALL REAR CONSOLE BOX UPPER FRONT PANEL SUB-ASSEMBLY (See  INSTALLATION  ) 
  21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) (See  INSTALLATION  ) 
  22. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL (See  INSTALLATION  ) 
  23. INSTALL FRONT PILLAR GARNISH RH 
    1. w/ Curtain Shield Airbag:
      1. Remove the piece of cloth or nylon.
        Fig 21: Identifying Protective Cover
        G04835420Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 3 clamps.
    3. Connect the antenna connector.
      Fig 22: Locating Antenna Connector Clamps
      G04835376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. w/ Curtain Shield Airbag:
      1. Install 2 new special clips and the clip onto the front pillar garnish.
      2. Engage the 2 clips and the 2 claws and install the front pillar garnish.
        Fig 23: Identifying Front Pillar Garnish Clips & Claws - With Curtain Shield Airbag
        G04835422Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. w/o Curtain Shield Airbag:
      1. Engage the 2 clips and the 2 claws and install the front pillar garnish.
        Fig 24: Identifying Front Pillar Garnish Clips & Claws - Without Curtain Shield Airbag
        G04835375Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. INSTALL FRONT PILLAR GARNISH LH 
    1. w/ Curtain Shield Airbag:
      1. Remove the piece of cloth or nylon.
        Fig 25: Identifying Piece Of Cloth Or Nylon - With Curtain Shield Airbag
        G04835424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 4 clamps.
      Fig 26: Identifying Clamps
      G04835380Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. w/ Curtain Shield Airbag:
      1. Install 2 new special clips and the clip onto the front pillar garnish.
      2. Engage the 2 clips and the 2 claws and install the front pillar garnish.
        Fig 27: Identifying Front Pillar Garnish Clips & Claws - With Curtain Shield Airbag
        G04835426Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. w/o Curtain Shield Airbag:
      1. Engage the 2 clips and the 2 claws and install the front pillar garnish.
        Fig 28: Identifying Front Pillar Garnish Clips & Claws - Without Curtain Shield Airbag
        G04835379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. INSTALL CENTER PILLAR UPPER GARNISH RH 
    1. Engage the 2 hooks and 2 clips and install the center pillar upper garnish.
  26. INSTALL CENTER PILLAR UPPER GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 29: Identifying Center Pillar Upper Garnish Clips & Hooks
    G04835373Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Install the through anchor with the bolt.

      Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) 

      Fig 30: Locating Anchor Bolt
      G04835372Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side.

  29. INSTALL SEAT BELT ANCHOR COVER CAP 

    HINT:

    Use the same procedure for both sides.

    1. Engage the 3 claws and install the seat belt anchor cover cap.
      Fig 31: Identifying Seat Belt Anchor Cover Cap Claws
      G04835430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. INSTALL CENTER PILLAR LOWER GARNISH RH 
    1. Engage the 2 clips and 3 claws and install the center pillar lower garnish.
  31. INSTALL CENTER PILLAR LOWER GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 32: Identifying Center Pillar Lower Garnish Clips & Claws
    G04835370Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. INSTALL ROOF SIDE INNER GARNISH RH 
    1. w/ Curtain Shield Airbag:
      1. Install a new special clip and the clip onto the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.
        Fig 33: Identifying Roof Side Inner Garnish Clips & Claws
        G04835368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/o Curtain Shield Airbag:
      1. Engage the 4 clips and the claw and install the roof side inner garnish.
  33. INSTALL ROOF SIDE INNER GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 34: Identifying Roof Side Inner Garnish Clips & Claws
    G04835369Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. INSTALL REAR SEAT SIDE COVER RH 
    1. Engage the 2 clips and the 4 claws and install the rear seat side cover.
  35. INSTALL REAR SEAT SIDE COVER LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 35: Identifying Rear Seat Side Cover Clips & Claws
    G04835434Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in Fig 36 .

      Paint mark 

      PAINT MARK LOCATION

      Area Color
      RH side Green
      LH side Red
  37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 36: Aligning Location Mark With Paint Mark
    G04835435Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. INSTALL REAR DOOR SCUFF PLATE RH 
    1. Engage the 7 claws and install the rear door scuff plate.
  39. INSTALL REAR DOOR SCUFF PLATE LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 37: Identifying Rear Door Scuff Plate Claws
    G04835365Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in Fig 38 .

      Paint mark 

      PAINT MARK LOCATION

      Area Color
      RH side Blue
      LH side Pink
  41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 38: Aligning Location Mark With Paint Mark
    G04835437Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  42. INSTALL COWL SIDE TRIM BOARD RH 
    1. Engage the stud bolt and the claw and install the cowl side trim board.
  43. INSTALL COWL SIDE TRIM BOARD LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 39: Identifying Cowl Side Trim Board Stud Bolt & Claw
    G04835363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH 
    1. Engage the 4 claws and install the instrument panel under cover.
      Fig 40: Identifying Instrument Panel Under Cover Claws
      G04835361Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH 
    1. Engage the 3 claws and install the instrument panel under cover.
    2. Tighten the 2 screws.
      Fig 41: Identifying Instrument Panel Under Cover Sub-Assembly Claws
      G04835362Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. INSTALL FRONT DOOR SCUFF PLATE RH 
    1. Engage the 11 claws and install the front door scuff plate.
  47. INSTALL FRONT DOOR SCUFF PLATE LH 

    HINT:

    Use the same procedure as for the RH side.

  48. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type) (See  INSTALLATION  ) 
  49. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type) (See  INSTALLATION  ) 
  50. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type) (See  INSTALLATION  ) 
  51. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type) (See  INSTALLATION  ) 
    Fig 42: Identifying Front Door Scuff Plate Claws
    G04835360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  52. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type) (See  INSTALLATION  ) 
  53. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) (See  INSTALLATION  ) 
  54. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY 
    1. for 60/40 Split Seat Type:
      1. Install the rear seat cushion cover pad sub-assembly (See INSTALLATION ).
    2. for Fixed Seat Type:
      1. Install the rear seat cushion cover pad sub-assembly (See INSTALLATION ).
  55. INSTALL FRONT SEAT ASSEMBLY LH (See  INSTALLATION  ) 
  56. INSTALL FRONT SEAT ASSEMBLY RH 

    HINT:

    Use the same procedure as for the LH side.

  57. INSTALL FRONT SEAT HEADREST ASSEMBLY 

    HINT:

    Use the same procedure for both sides.

    1. Push in the lock button of the front seat headrest support and install the front seat headrest.
  58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  59. INSPECT SRS WARNING LIGHT (See  DIAGNOSIS SYSTEM  ) 
    Fig 43: Identifying Lock Button
    G04835359Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals