Remove/install windshield - AR67.10-P-1000P
MODEL 169, 171, 203, 207, 209, 211, 212.1 /2, 218, 230.4, 240, 245.2
MODEL 212.0 except CODE (Z04) Light armoring
Illustrated on model 203.0
| Removing | |||
| Risk of injury caused by moving parts that can pinch, crush or, in extreme cases even sever extremities. | Always remove ignition key when working on windshield wiper mechanism. | AS82.30-Z-0001-01A | |
| Notes on removal/installation of windshield | AH67.10-P-1000-01P | ||
| Notes on carrying out repair work in the vehicle interior | Model 240 | AH68.00-P-0001-01H | |
| 1 | Prepare 1-component adhesive cartridge | AR67.10-P-1000-12SX | |
| Figure | |||
| Cartridge preheater (not regulated), cartridge gun gotis://K_67.0_02.0 Repair kit |
*BR00.45-Z-1089-02A | ||
| Repair kit | *BR00.45-Z-1035-02B | ||
| 2 | Open side window in driver door | ||
| 3 | Remove detachable parts when replacing windshield (1). | Model 169 | AR67.10-P-1050AK |
| Model 171 | AR67.10-P-1050V | ||
| Model 203.0/2/7 | AR67.10-P-1050P | ||
| Model 207 | AR67.10-P-1050EC | ||
| MODEL 209 | AR67.10-P-1050Q | ||
| Model 211.0/2/6 | AR67.10-P-1050T | ||
| Model 212 | AR67.10-P-1050EW | ||
| Model 218 | AR67.10-P-1050EL | ||
| Model 230.4 | AR67.10-P-1050R | ||
| Model 240 | AR67.10-P-1050H | ||
| Model 245.2 | AR67.10-P-1050BK | ||
| 4 | Cover dashboard | ||
| Risk of injury due to tear or warming up of cutting wire and through glass splinters when cutting out glued windows | Wear protective gloves and safety glasses. | AS67.00-Z-0004-01A | |
| 5 | Cut out windshield (1) with Roll Out 2004 window removal tool | Roll out 2004 window removal tool gotis://K_67.0_01.0 Suction lifting device gotis://K_67.0_03.0 |
AR67.10-P-1000-11SX |
| Install | |||
| 6 | Remove silicon gel on rain/light sensor (B38/2) from windshield (1) | Model 169, 245.2 with code (U58) Exterior light & vision package or with code (345) Rain sensor |
|
| 7 | Prepare body flange for installation of window | AR67.10-P-1501-01P | |
| Wet and dry vacuum cleaner gotis://P_00.12_06. |
|||
| Repair kit | *BR00.45-Z-1015-02A | ||
| Repair kit | *BR00.45-Z-1089-02A | ||
| Repair kit | *BR00.45-Z-1035-02B | ||
| Repair stick | *BR00.45-Z-1050-07A | ||
| Hepox 2K EP primer filler 4017 (Spray Max) | *BR00.45-Z-1050-07A | ||
| General notes about painting the body flange in the glazing area | Pay attention to notes concerning the preparation of new parts such as the A-pillar, the roof or the side walls. | AH98.00-P-9408-06A | |
| 8 | Transfer detachable parts on windshield (1). | ||
| 9 | Prepare windshield (1) for glazing | AR67.10-P-1000-03P | |
| Repair kit | *BR00.45-Z-1015-02A | ||
| Repair kit | *BR00.45-Z-1089-02A | ||
| Repair kit | *BR00.45-Z-1035-02B | ||
| 10.1 | Replace rubber window spacers | ||
| Model 169, 245.2 | AR67.10-P-1000-02AK | ||
| Model 171 | AR67.10-P-1000-02V | ||
| Model 203, 209 | AR67.10-P-1000-02P | ||
| Model 207, 211.0/2/6, 212, 218 | AR67.10-P-1000-02T | ||
| Model 230.4 | AR67.10-P-1000-02R | ||
| 10.2 | Replace rubber spacers | Model 240 | AR67.20-P-2000-03H |
| Washer | *BR00.45-Z-1006-10A | ||
| Washer | *BR00.45-Z-1007-10A | ||
| Spacer | *BR00.45-Z-1008-10A | ||
| 11 | Align windshield (1) in the body opening | Observe dimensions and gap dimensions. |
|
| Figure | |||
| Suction lifting device gotis://K_67.0_03.0 |
|||
| Model 169, 171, 207, 209, 212, 218, 230.4, 245.2 | AR67.10-P-1000-04G | ||
| Distance between top edge of window and front edge of roof (on model 171, 209, 230) | *BE67.10-P-1001-01A | ||
| Distance between top edge of window and front edge of roof (on model 169, 245) | *BE67.10-P-1001-01E | ||
| Distance between top edge of window and transition between rabbet and front edge of roof (on model 207, 212, 218) | *BE67.10-P-1001-01G | ||
| Model 203 except code (413) Panoramic sliding roof, except model 203.7 | AR67.10-P-1000-04P | ||
| Distance between top edge of window and front edge of roof | *BE67.10-P-1001-01G | ||
| Model 203.7 with code (413) Panorama sliding roof. | AR67.10-P-1000-04P | ||
| Gap dimensions | *BE67.10-P-1007-01A | ||
| Model 211.0/2/6 | AR67.10-P-1000-04T | ||
| Distance between molding on windshield and front edge of roof (without (413) Panoramic sliding roof, code (419) Solar module for panoramic sliding roof) | *BE67.20-P-1001-01C | ||
| Distance between top edge of window and base center point for mounting clip on trim strip (with code (413) Panoramic sliding roof, code (419) Solar module for panoramic roof) | *BE67.10-P-1002-01C | ||
| 12 | Remove protective foil from rubber window spacers. | Except model 240 | |
| 13 | Apply adhesive material | Figure | |
| Cartridge gun gotis://K_67.0_02.0 |
|||
| Model 169, 171, 203, 207, 209, 211, 212, 218, 230.4, 245.2 | AR67.10-P-1000-08P | ||
| Repair kit | *BR00.45-Z-1015-02A | ||
| Repair kit | *BR00.45-Z-1089-02A | ||
| Repair kit | *BR00.45-Z-1035-02B | ||
| Model 240 | AR67.10-P-1000-08H | ||
| Repair kit | *BR00.45-Z-1089-02A | ||
| 14 | Install windshield (1) | Suction lifting device gotis://K_67.0_03.0 |
|
| Model 169, 171, 203, 207, 209, 211, 212, 218, 230.4, 245.2 | AR67.10-P-1503-01P | ||
| Model 240 | AR67.10-P-1503-01H | ||
| 15 | Install detachable parts when replacing windshield (1). | Model 169 | AR67.10-P-1050AK |
| Model 171 | AR67.10-P-1050V | ||
| Model 203.0/2/7 | AR67.10-P-1050P | ||
| Model 207 | AR67.10-P-1050EC | ||
| MODEL 209 | AR67.10-P-1050Q | ||
| Model 211.0/2/6 | AR67.10-P-1050T | ||
| Model 212 | AR67.10-P-1050EW | ||
| Model 218 | AR67.10-P-1050EL | ||
| Model 230.4 | AR67.10-P-1050R | ||
| Model 240 | AR67.10-P-1050H | ||
| Model 245.2 | AR67.10-P-1050BK | ||
| 16 | Remove cover from dashboard | ||
| 17 | Select adaptation of rain sensor, light sensor reinforcement factor with coding as well as windshield variant and perform with Star Diagnosis | Model 171, 203, 207, 209, 211, 212, 218, 240 Model 169, 245.2 with code (U58) Exterior light & vision package Model 230.4 only when replacing windshield (1). |
AD00.00-P-2000-04A |
| 18 | Check all electrical consumers in area repaired for proper function. | ||
| 19 | Close side window in driver door | ||
| 20 | Clean windshield (1) and passenger compartment |
TEST AND ADJUSTMENT VALUES FOR WINDSHIELD
| Number | Designation | Model 170, 171 | Model 203 | ||
|---|---|---|---|---|---|
| BE67.10-P-1001-01A | Distance between window upper edge and front edge of roof | Dimension "A" | mm | 12 | 12 |
| See picture | AR67.10-P-1000-04G | AR67.10-P-1000-04E | |||
TEST AND ADJUSTMENT VALUES FOR WINDSHIELD
| Number | Designation | Type 209.3 | Type 209.4 | Model 230 | ||
|---|---|---|---|---|---|---|
| BE67.10-P-1001-01A | Distance between window upper edge and front edge of roof | Dimension "A" | mm | 3 | 9 | 10 |
| See picture | - | - | - | |||
CHECK VALUES FOR WINDSHIELD
| Number | Designation | Model 211 without code 413, 419 | Model 211 with code 413, 419 | |
|---|---|---|---|---|
| BE67.10-P-1001-01C | Distance between molding on windshield and front edge of roof | mm | 2 | - |
| BE67.10-P-1002-01C | Distance between top edge of window and base center point of clip attaching trim strip at top | mm | - | 4.5 |
TEST AND ADJUSTMENT VALUES FOR WINDSHIELD
| Number | Designation | Model 169 | Model 245 | ||
|---|---|---|---|---|---|
| BE67.10-P-1001-01E | Distance between top edge of window and front edge of roof | Dimension "A" | mm | 4 | 4 |
| See picture | AR67.10-P-1000-04G | AR67.10-P-1000-04G | |||
TEST AND ADJUSTMENT VALUES FOR WINDSHIELD
| Number | Designation | Model 207 | Model 212 | ||
|---|---|---|---|---|---|
| BE67.10-P-1001-01G | Distance between top edge of window and transition between rabbet and front edge of roof | Dimension "a" | mm | 3.5 (±1) | 5 (±1) |
| See picture | - | - | |||
TEST AND ADJUSTMENT VALUES FOR WINDSHIELD
| Number | Designation | Model 218 | ||
|---|---|---|---|---|
| BE67.10-P-1001-01G | Distance between top edge of window and transition between rabbet and front edge of roof | Dimension "a" | mm | 3.5 (±1) |
| See picture | - | |||
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Model 203.7 | ||
|---|---|---|---|---|
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | 2 (± 1) |
| Tilting/sliding roof to glass roof, rear | mm | 2 (± 1) | ||
| Glass roof, rear, to rear window | mm | 9 (± 1) | ||
| Windshield to outer mounting clamp of trim strip | mm | 7 (± 1) | ||
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1015-02A | Repair kit, glazing, installing window, 2-component adhesive | A 220 670 00 93 |
| BR00.45-Z-1089-02A | Repair kit, installing window, 1-component adhesive, replaced by: A 221 670 81 01 | A 221 670 21 01 |
| BR00.45-Z-1035-02B | Repair kit, installing windshields, 1-component adhesive | A 221 670 81 01 |
| BR00.45-Z-1012-07A | Primer stick | A 000 986 27 50 |
| BR00.45-Z-1050-07A | Hepox 2K EP primer filler 4017 (Spray Max) | Spies Hecker GmbH Fritz-Hecker-Str. 47-107 50968 Koln Germany Tel. +49 221 370606 Fax. +49 221 3706410 www.spieshecker.com |
| BR00.45-Z-1006-10A | Base, rear-end door window 14 X 8 X 5 mm | A 210 671 03 97 |
| BR00.45-Z-1007-10A | Base, side window at side wall 20 X 6.5 X 5 mm | A 240 671 00 97 |
| BR00.45-Z-1008-10A | Spacer | A 356 693 00 44 |