Section 1730 (Automatic Transmission - 4L60-E/4L65-E/4L70-E - Repair Instructions - Off Vehicle)
WARNING: This page is about a different car, the 2010 GMC Sierra and 2010 Chevrolet Silverado. However, it is still accessible from the selected car via links, so may be relevant.
- Repair Instructions - Off Vehicle
- Holding Fixture Installation
- Torque Converter Assembly Removal
- Drain Oil
- Converter Housing Removal
- 2-4 Servo Cover and Assembly Removal
- 2-4 Band Servo Piston Pin Length Check
- Vehicle Speed Sensor and Case Extension Removal
- Transmission Fluid Pan and Filter Assembly Removal
- Control Valve Body and Wiring Harness Removal
- Turbine Shaft O-Ring Removal
- Transmission End Play Check
- Oil Pump Removal
- 2-4 Band, Input Clutches, Input Gear Set Removal
- Reaction Gear Set Removal
- Output Shaft, Reaction Gear, Low/Rev Clutch Removal
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Removal
- Low and Reverse Clutch Piston Removal
- Case Assembly Inspection
- 3rd Accumulator Retainer with Ball Assembly Leak Check
- 3rd Accumulator Retainer with Ball Replacement
- Case Bushing
- Manual Shift Shaft Seal Installation
- Low and Reverse Clutch Piston Installation
- Manual Shift Detent Lever with Shaft Position Switch Assembly and Park Pawl Actuator Installation
- Reaction Gear and Carrier Inspection
- Reaction Gear and Carrier Installation
- Low and Reverse Clutch Spacer Plate Selection
- Low and Reverse Clutch Plate Installation
- Low and Reverse Clutch Support Disassemble
- Low and Reverse Clutch Support Installation
- Reaction Sun Gear Installation
- Reaction Carrier Shaft Replacement
- Input Internal Gear, Reaction Shaft and Shell Installation
- Internal Transmission Speed Sensor Rotor Replacement
- Output Shaft Installation
- Input Carrier Inspection
- Input Sun Gear Bushing Replacement
- Input Carrier Inspection and Installation
- Input Clutch Assembly Disassemble
- Input Housing and Shaft Assembly Inspection
- Input Housing and Shaft Assembly Assemble
- Input Housing to Output Shaft Seal Installation
- Overrun Clutch Installation
- Forward Clutch Sprag Disassemble
- Forward Clutch Sprag Assemble
- Forward Clutch Assembly Assemble
- Forward Clutch Piston Travel Check
- 3-4 Clutch Assemble
- 3-4 Clutch Plate Travel Check
- Clutch Air Check
- Turbine Shaft Seal Installation
- Reverse Input Clutch Disassemble
- Reverse Input Clutch Bushing Replacement
- Reverse Input Clutch Assemble
- Reverse Input Clutch Plate Travel Check
- Reverse Input and 3-4 Clutch Housing Installation
- 2-4 Band Installation
- Input Speed Sensor Removal
- Oil Pump Disassemble
- Oil Pump Body Disassemble
- Fluid Pump Rotor and Slide Measurement
- Oil Pump Body Bushing Replacement
- Oil Pump Body Assemble
- Oil Pump Cover Disassemble
- Oil Pump Stator Shaft Bushing Replacement
- Oil Pump Cover Assemble
- Oil Pump Cover and Body Assemble
- Input Speed Sensor Installation
- Oil Pump Assembly Installation
- Converter Housing Installation
- Turbine Shaft O-Ring Installation
- Control Valve Body Disassemble
- Control Valve Body Assemble
- 3-4 Accumulator Installation
- 1-2 Accumulator Disassemble
- 1-2 Accumulator Assemble
- 1-2 Accumulator Installation
- Control Valve Body Installation
- Manual Detent Spring Installation
- Oil Filter Assembly Installation
- Transmission Fluid Pan Installation
- 2-4 Band Servo 2nd Apply Piston Disassemble
- 2-4 Servo Assembly Installation
- Case Extension Bushing Replacement
- Vehicle Speed Sensor and Case Extension Installation
- Torque Converter End Play Inspection
- Torque Converter Installation
- Holding Fixture Removal