Install the sealing cap on the cylinder head of cylinder bank 1

• Replace the seal (1).

  Parts:  Gasket

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the sealing cap (2) on the cylinder head.
• Tighten down screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Sealing cap to cylinder head
  M6x20 screw	Tightening torque  9.5 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 1 .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR INTAKE OF CYLINDER BANK 1 .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 1 TO 4 .
• Refer to SECURING THE WIRING HARNESS SECTION OF THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING RIGHT HIGH PRESSURE PUMP .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING THE RIGHT HIGH-PRESSURE RAIL .
• Refer to INSTALLING GUIDE TUBE FOR OIL DIPSTICK .
• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE OIL FILLER CAP .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING DRIVE BELT .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 1 .
• Refer to INSTALLING IGNITION COILS FROM CYLINDER BANK 1 .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE INTAKE PIPE OF THE ENGINE VENTILATION LINE .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 1 TO 4 .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE CARRIER PLATE .
• Refer to INSTALLING THE CATALYTIC CONVERTER OF CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
• Refer to INSTALLING HEAT SHIELD, TOP .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
• Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
• Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .
• Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT PUMP .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING THE RIGHT AND LEFT UNFILTERED-AIR DUCT .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING THE RIGHT INTAKE SILENCER BRACKET .
• Refer to INSTALLING BOTH INTAKE FILTER HOUSING .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT , and INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE TOP RIGHT .