Installing left and right exhaust turbochargers

Loosen screws (2).
Remove oil return line (1).
Ensure that the sealing surfaces in the area of the oil return line are planar and free from oil and grease.
Replace the seal (3).
Parts: Seal

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the oil return line (3).
Parts: Oil return line
Replace the seal (1).
Parts: Seal
Position screws (2) in oil return line (3).
Slide seal (1) onto the screws (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Position the oil return line (1).

Tighten down screws (2).

TIGHTENING TORQUE SPECIFICATIONS

Oil return line at the exhaust turbocharger
M6x16 Replace screws.	Joining torque	5 Nm
M6x16 Replace screws.	Angle of rotation	60°

Make sure that the seal (3) does not fall out during the feed in.

Courtesy of BMW OF NORTH AMERICA, INC.
Check oil feed line for contamination or obstruction and clean or replace as needed.
If the oil feed line is heavily contaminated, it is recommended to change the engine oil and oil filter.
Check the clean air ducts on the intake side and charge air cooler for contamination or foreign bodies and clean if necessary.
If installed: Check the coolant feed lines and return lines for exhaust turbocharger for contamination or obstruction, clean or replace if necessary.
Check that screw connections and plug connections for all lines are correct.
Check air cleaner for contamination and clean or replace as needed.
Check correct functioning of crankcase ventilation.
Replace all gaskets.
Parts: Seals
Replace O-ring (1).
Parts: O-ring
Make sure that the O-ring (1) does not fall into the oil duct in the engine block.
If the O-ring (1) cannot be disassembled, the oil return lid must be disassembled.
Coat O-ring (1) with engine oil.

Courtesy of BMW OF NORTH AMERICA, INC.

ENGINE OIL DESCRIPTION

Technically suitable engine oils for BMW Group engines
Thread in exhaust turbocharger with oil return line in downward direction and position it.
Make sure that the oil return line is not mechanically deformed.
Connect connectors (1) and lock.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the V-clip (2).
Parts: V-band clamp
Position V-clip (2).
Hand-tighten the bolt (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten screw (1) on the V-clip.

TIGHTENING TORQUE SPECIFICATIONS

Exhaust turbocharger to exhaust manifold
V-band clamp Replace V-band clamp.	Tightening torque	9 Nm
V-band clamp Replace V-band clamp.	Tightening torque	20 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Check if the screw connection of the V-band clamp is too loose.
If there is a gap between the ends of the V-band clamps: Loosen the screw and tighten again.

Courtesy of BMW OF NORTH AMERICA, INC.
Check if the screw connection of the V-band clamp is too tight.
When the ends of the V-band clamp are positioned one below the other: Loosen screws and retighten.

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure that the ends of the V-band clamp are parallel to each other.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Remove special tool 2 249 171 (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the screw (1).
Parts: Screw
Replace the sealing ring or sealing rings (2).
Parts: Sealing ring or sealing rings
Make sure that when installing sealing rings without a fitting aid (bridge), both sealing rings are replaced.
Position screw (1) with the sealing ring or sealing rings (2) on the oil feed line.
Position oil feed line.

Courtesy of BMW OF NORTH AMERICA, INC.

Determining the screw type and selecting the appropriate socket wrench:

Screw type	Matching socket wrench
Hexagon screw (3)	Commercial socket wrench (1)
Multi-tooth screw (4)	Multi-tooth socket wrench (2)

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Oil feed line to exhaust turbocharger
Banjo bolt M10x1 Replace screw.	Joining torque	8 Nm
Banjo bolt M10x1 Replace screw.	Angle of rotation	70°

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Oil feed line holder to exhaust turbocharger
M6x16 screw	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Installing right exhaust turbocharger

Loosen screws (2).
Remove oil return line (1).
Make sure that the sealing surfaces in the area of the oil return line (1) are flat and free of grease.
Replace the seal (3).
Parts: Seal

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the oil return line (3).
Parts: Oil return line
Replace the seal (1).
Parts: Seal
Replace screws (2).
Parts: Screws
Position screws (2) in oil return line (3).
Slide seal (1) onto the screws (2).

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
Complete the following steps with the help of a support person.
Position the oil return line (1).

Tighten screws (2) with an electronic torque wrench with tightening angle display.

TIGHTENING TORQUE SPECIFICATIONS

Oil return line at the exhaust turbocharger
M6x16 Replace screws.	Joining torque	5 Nm
M6x16 Replace screws.	Angle of rotation	60°

Courtesy of BMW OF NORTH AMERICA, INC.

Make sure that the seal (3) does not fall out during the feed in.
Check oil feed line for contamination or obstruction and clean or replace as needed.
If the oil feed line is heavily contaminated, it is recommended to change the engine oil and oil filter.
Check the clean air lines on the intake side and the charge air cooler for contamination or foreign bodies, and clean if necessary.
If installed: Check the coolant feed lines and coolant return lines for the exhaust turbocharger for contamination or obstruction and clean or replace as needed.
Check the screw connections and plug connections of all lines for accuracy.
Check air cleaner for contamination and clean or replace as needed.
Check correct functioning of crankcase ventilation.
Replace all gaskets.
Parts: Seals
Replace O-ring (1).
Parts: O-ring
Make sure that the O-ring (1) does not fall into the oil duct in the engine block.
If the O-ring (1) cannot be disassembled, the oil return lid must be disassembled.
Coat O-ring (1) with engine oil.
ENGINE OIL DESCRIPTION

Technically suitable engine oils for BMW Group engines

Courtesy of BMW OF NORTH AMERICA, INC.
Thread in exhaust turbocharger with oil return line in downward direction and position it.
Make sure that the oil return line is not mechanically deformed.
Connect connectors (1) and lock.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the V-clip (2).
Parts: V-band clamp
Position V-clip (2).
Hand-tighten the bolt (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Position special tool 2 249 171 (2) on cylinder head covers.

Tighten special tool 2 249 171 (2) with screws (1) on cylinder head covers. Note the screw length while doing so.

TIGHTENING TORQUE SPECIFICATIONS

Gauge of exhaust turbocharger to cylinder head cover
screw	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Manually move the screws (1) of the setting gauge up to the contact surface of the exhaust turbocharger (2).
Exhaust turbocharger (2) must be aligned on vertical axis on left and right.
Adjust exhaust turbocharger (2) parallel to setting gauge.

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten screw (1) on the V-clip.

TIGHTENING TORQUE SPECIFICATIONS

Exhaust turbocharger to exhaust manifold
V-band clamp Replace V-band clamp.	Tightening torque	9 Nm
V-band clamp Replace V-band clamp.	Tightening torque	20 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Check if the screw connection of the V-band clamp is too loose.
If there is a gap between the ends of the V-band clamps: Loosen the screw and tighten again.

Courtesy of BMW OF NORTH AMERICA, INC.
Check if the screw connection of the V-band clamp is too tight.
When the ends of the V-band clamp are positioned one below the other: Loosen screws and retighten.

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure that the ends of the V-band clamp are parallel to each other.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Remove special tool 2 249 171 (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Oil return line to crankcase
screw	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Push hose clamps (1) onto hoses.
Push the hoses onto the connections.
Secure hose clamps (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the screw (1).
Parts: Screw
Replace the sealing ring or sealing rings (2).
Parts: Sealing ring or sealing rings
Make sure that when installing sealing rings without a fitting aid (bridge), both sealing rings are replaced.
Position screw (1) with the sealing ring or sealing rings (2) on the oil feed line.
Position oil feed line.

Courtesy of BMW OF NORTH AMERICA, INC.

Determining the screw type and selecting the appropriate socket wrench:

Screw type	Matching socket wrench
Hexagon screw (3)	Commercial socket wrench (1)
Multi-tooth screw (4)	Multi-tooth socket wrench (2)

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten screw (1) by hand.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten screw (1) by hand.

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (2).

TIGHTENING TORQUE SPECIFICATIONS

Oil feed line holder to exhaust turbocharger
M6x16 screw	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Oil feed line to exhaust turbocharger
Banjo bolt M10x1 Replace screw.	Joining torque	8 Nm
Banjo bolt M10x1 Replace screw.	Angle of rotation	70°

Follow-up work

Mounting fixture on the right.

Courtesy of BMW OF NORTH AMERICA, INC.

Position fixture for the right (2).
Tightening the screws (1).

Tightening torques

Mount
M6x16	Tightening torque	8 Nm

Refer to INSTALLING LEFT MOUNT .
Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
Installing clean air pipe of cylinder bank 1.

Courtesy of BMW OF NORTH AMERICA, INC.
- Position the clean air pipe of cylinder bank 1 (2) in direction of arrow and slide it on
The retaining clip (1) must engage audibly.
Refer to INSTALLING CATALYTIC CONVERTER NEAR THE ENGINE ABOVE CYLINDER BANK 1 .
Refer to INSTALLING UPPER CATALYTIC CONVERTER NEAR ENGINE FOR BANK 2 .
Refer to INSTALLING HEAT SHIELD, TOP .

Installing conduit on bank 2

Courtesy of BMW OF NORTH AMERICA, INC.

Clip the wiring harness (2) into the clamps (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Position the wiring harness.

Tighten down screws (1).

TIGHTENING TORQUES

Cable duct
M6x16 screw	Tightening torque	10Nm

Refer to INSTALLING ENGINE VENTILATION LINE OF CYLINDER BANK 1 .
Refer to INSTALLING THE HOLDER WITH THE VEHICLE WIRING HARNESS FOR THE SENSOR SYSTEM OF CYLINDER BANK 1 .
Refer to INSTALLING THE TANK VENTILATION LINE OF CYLINDER BANK 1 PARTIALLY .

Installing cable duct at cylinder bank 1.

Courtesy of BMW OF NORTH AMERICA, INC.

Position the conduit (2).
Tighten the screws (1).

TIGHTENING TORQUES

Cable duct
M6x16 screw	Tightening torque	10Nm

Refer to INSTALLING THE OXYGEN SENSOR MONITOR OF CYLINDER BANK 1 .
Refer to INSTALLING THE OXYGEN SENSOR MONITOR OF CYLINDER BANK 2 .
Refer to CHECKING THE POSITION OF THE HEAT SHIELD .
Refer to INSTALLING THE EXPANSION TANK FOR THE CHARGE AIR COOLER .
Refer to INSTALLING HOLDER OF THE DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
Refer to INSTALLING COOLANT EXPANSION TANK .
Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR THE CYLINDERS 5 TO 8 .
Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR THE CYLINDERS 1 TO 4 .
Refer to INSTALLING THE CHARGE AIR COOLER ON THE LEFT AND RIGHT .
Refer to CLOSING THE COOLANT PUMPS .
Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
Refer to INSTALLING THE STIFFENING PLATE .
Refer to INSTALLING THE FRONT RIGHT WHEEL .
Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
Refer to INSTALLING FAN COWL WITH ELECTRIC MOTOR .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
Refer to INSTALLING FRONT CROSS CONNECTION .
Refer to TIGHTENING THE LEFT FRONT-END STRUT .
Refer to TIGHTENING THE FRONT-END STRUT ON THE RIGHT .
Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE RIGHT .
Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE LEFT .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Installing the rear right engine compartment cover.

Courtesy of BMW OF NORTH AMERICA, INC.

Remove the battery cover .

NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
- Remove the special tool 2 452 007 from the battery.
Courtesy of BMW OF NORTH AMERICA, INC.
- Install the cover (2).
- Lock the lock (1).
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .
Refer to INSTALLING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
Refer to CONNECTING BATTERY GROUND LEAD . .
Refer to CHECKING ENGINE OIL LEVEL .