Installing intake camshaft of cylinder bank 2
- Plastic rings (1) are maintenance free and do not need to be replaced.
- Check plastic rings for damage, replace if necessary.
NOTE:
TECHNICAL INFORMATION
The rocker arms may slip slightly when the camshaft is positioned. Make sure rocker arms are correctly positioned on the hydraulic valve clearance compensating elements and on valves.
The rocker arms may slip slightly when the camshaft is positioned. Make sure rocker arms are correctly positioned on the hydraulic valve clearance compensating elements and on valves.
- Position intake camshaft.
- When screwing the camshafts, make sure the valves have free movement
.
- Position guide bearing shells according to marks (E1) to (E5) .
- Join the screws of the guide bearings with position numbers (1) and (4) in multiple steps by one half turn at a time until flush.
- Tighten the screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Intake/exhaust camshaft | ||
|---|---|---|
| M6 | Snug torque | 10 Nm |
| Tightening torque | 10.5 Nm | |
- Tighten down screws (4) .
TIGHTENING TORQUE SPECIFICATIONS
| Intake/exhaust camshaft | ||
|---|---|---|
| M6 | Snug torque | 10 Nm |
| Tightening torque | 10.5 Nm | |
- All intermediate levers (3) must rest correctly on the idler pulley (1) and on the camshaft (4) .
- All intermediate levers (3) must rest correctly on the idler pulley (2) and on the eccentric shaft (5) .
Follow-up work
- INSTALLING THE SLIDING BLOCK OF CYLINDER BANK 2 .
- INSTALLING TORSION SPRINGS .
- REMOVING CYLINDER HEAD OF BANK 2 FROM ASSEMBLY JIG .
- INSTALLING THE LEFT VALVETRONIC SERVOMOTOR (CYLINDER HEAD REMOVED) .
- INSTALLING THE LEFT INTAKE PLENUM (CYLINDER HEAD REMOVED) .
- INSTALLING THE LEFT CYLINDER HEAD .
- INSTALLING BOTH LEFT VANOS ADJUSTERS .
- REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
- INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
- INSTALLING THE TIMING CASE COVER ON THE CYLINDER HEAD OF CYLINDER BANK 2 .
- INSTALLING THE LEFT CYLINDER HEAD COVER .
- INSTALLING THE PRESSURE LINE BETWEEN THE EVAPORATOR AND AIR CONDITIONING CONDENSER .
- INSTALLING OIL FEED LINE ON EXHAUST TURBOCHARGER CYLINDERS 5 TO 8 .
- INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
- INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2 .
- INSTALLING THE LEFT HIGH PRESSURE PUMP .
- INSTALLING FUEL DELIVERY LINE .
- INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
- INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
- INSTALLING THE IGNITION COILS OF CYLINDER BANK 2 .
- INSTALLING THE IGNITION COILS OF CYLINDERS 1 AND 5 .
- INSTALLING BOTH EXHAUST TURBOCHARGERS .
- INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
- INSTALLING CLEAN AIR PIPE OF CYLINDER BANK 1 .
- INSTALLING BOTH CHARGE AIR COOLERS .
- CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
- CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
- CLOSING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
- INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT (CHARGE AIR COOLER) .
- SEALING OFF COOLANT FOR LOW-TEMPERATURE COOLANT CIRCUIT .
- INSTALLING COOLANT PUMPS .
- INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- INSTALLING FRONT UNDERBODY PROTECTION .
- INSTALLING THE BOTTOM FRONT RIGHT SIDE COVER .
- INSTALLING DRIVE BELT .
- INSTALLING FAN COWL .
- INSTALLING THE REAR TOP CROSS CONNECTION .
- INSTALLING UPPER CROSS CONNECTION .
- INSTALLING BOTH FRONT-END STRUTS .
- INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
- INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 5 TO 8 .
- RELEASING THE HEAT SHIELD .
- INSTALLING THE CENTER COWL UPPER PART .
- INSTALLING TENSION STRUT ON SHOCK TOWER .
- ATTACHING WINDSHIELD PANEL COVER .
- INSTALLING LEFT AND RIGHT WIPER ARM .
- INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- INSTALLING RIGHT HEAT SHIELD .
- INSTALLING LEFT HEAT SHIELD .
- INSTALLING HEAT SHIELD, TOP .
- INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
- INSTALLING THE LEFT OXYGEN SENSOR MONITOR .
- PARTIALLY INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
- PARTIALLY INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
- INSTALLING THE RETAINING BRIDGE IN VEHICLES WITH A GASOLINE PARTICULATE FILTER .
- INSTALLING THE RETAINING BRIDGE .
- INSTALLING EXHAUST SYSTEM .
- INSTALLING CENTER STIFFENING PLATE .
- INSTALLING TANK COVER ON LEFT AND RIGHT .
- INSTALLING REAR PANEL .
- INSTALLING THE CONTROL UNIT BRACKET FOR CYLINDERS 5 TO 8 .
- INSTALLING THE COVER OF THE LEFT DME CONTROL UNIT .
- INSTALLING CONTROL UNIT HOLDER FOR CYLINDERS 1 TO 4 .
- INSTALLING THE COVER OF THE RIGHT DME CONTROL UNIT .
- PARTIALLY INSTALLING THE REAR LEFT AND RIGHT WHEEL ARCH COVERS .
- INSTALLING BOTH EXHAUST COVERS .
- INSTALLING BOTH SIDE REAR TRIM STRIPS .
- INSTALLING THE REAR BUMPER TRIM .
- INSTALLING THE REAR DIFFUSER .
- INSTALLING THE TAIL LIGHT ON THE LEFT AND RIGHT SIDE PANELS .
- INSTALLING COVER FOR WATER CHANNEL ON LEFT AND RIGHT .
- INSTALLING THE LUGGAGE COMPARTMENT WHEEL ARCH TRIM PANEL ON THE LEFT AND RIGHT (PARTIALLY REMOVED) .
- INSTALLING BOTH LEDs IN THE CARGO AREA .
- INSTALLING LOADING EDGE TRIM .
- INSTALLING LUGGAGE COMPARTMENT FLOOR COVERING .
- ACTIVATING ELECTRICAL SYSTEM .
- FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
- FILLING AND VENTING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
- EVACUATING AND CHARGING CONDITIONING .