Installing the head-up display

• Connect the associated connector with the head-up display (2)  .
• Guide the Head-Up Display (2)  into the support.
• Tighten down screws (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Head-Up Display to support
  M6x25 screw	Tightening torque	4.5 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Correctly position support for the dashboard.
• Install the nuts (1)  and (2)  and tighten.
  TIGHTENING TORQUES SPECIFICATION
  
  

  Support for dashboard
  Nut M8	tightening torque	21 Nm
  M8 screw	tightening torque	21 Nm
  Nut M6	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install the retainer on the left and right and tighten the nuts (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Support for dashboard on bottom
  Nut M8	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten nuts (2)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Support for dashboard
  Nut M8	tightening torque	21 Nm
  M8 screw	tightening torque	21 Nm
  Nut M6	tightening torque	8 Nm

• Tighten nuts (1)  .
• Tighten down screws (2)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Support for dashboard
  Nut M8	tightening torque	21 Nm
  M8 screw	tightening torque	21 Nm
  Nut M6	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

  Securing the steering shaft, bottom, to the steering column 

  NOTE: TECHNICAL INFORMATION 
  The steering shaft and the steering column are not encoded to each other. At the time of removal, installation and replacement, mark the positioning of the steering shaft in relation to the steering column. Non-compliance will lead to inclination of the steering wheel.
• Align the bottom steering shaft (2)  to the steering column using the mark (3)  that was made during the removal.
• Slide the bottom steering shaft (2)  onto the steering column.
• Replace the clamping bolt (1)  . Parts:  Clamping bolt
• Tighten the clamping bolt (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Lower steering shaft to steering column
  M8 Recut screw thread Replace clamping bolt. No retorque permitted!	tightening torque	28 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Push the refrigerant line (1)  to one side.
• Tighten down screw (2)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Support for dashboard
  Nut M8	tightening torque	21 Nm
  M8 screw	tightening torque	21 Nm
  Nut M6	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING DASHBOARD TRIM .
• Refer to INSTALLING THE MID-RANGE SPEAKERS IN THE DASHBOARD .
• Refer to INSTALLING THE INSTRUMENT CLUSTER (KOMBI) .
• Refer to INSTALLING THE HEAD UNIT HIGH (HU-H) (WITH BRACKET) .
• Refer to INSTALLING THE LIGHT OPERATING UNIT .
• Refer to REMOVING THE DECORATIVE STRIP FROM THE LEFT AND RIGHT DASHBOARD .
• Refer to INSTALLING THE SIDE COVER ON THE DASHBOARD AT LEFT AND RIGHT .
• Refer to INSTALLING THE TRIM FOR THE HEAD-UP DISPLAY .
• Refer to INSTALLING A-PILLAR TRIM PANEL, LEFT AND RIGHT .
• Refer to INSTALLING SIDE TRIM PANEL IN FOOTWELL ON RIGHT A-PILLAR .
• Refer to INSTALLING INSIDE RIGHT DOOR SILL COVER STRIP .
• Refer to INSTALLING THE CENTER CONSOLE .
• Refer to INSTALLING THE FOOTWELL TRIM PANEL ON THE RIGHT .
• Refer to INSTALLING THE TRIM PANEL FOR THE PEDAL ASSEMBLY .
• Refer to INSTALLING THE CENTER STACK MODULE .
• Refer to INSTALLING THE WIRELESS CHARGING STORAGE .
• Refer to INSTALLING THE CUP HOLDER .
• Refer to INSTALLING THE CENTRAL INFORMATION DISPLAY (CID) .
• Refer to INSTALLING THE SPEAKER TRIM AT THE DASHBOARD .
• Refer to INSTALLING CENTER ARMREST .
• Refer to INSTALLING THE CENTER ARMREST STORAGE COMPARTMENT .
• Refer to INSTALLING THE REAR CENTER CONSOLE TRIM .
• Refer to INSTALLING THE STEERING COLUMN SWITCH CLUSTER (SZL) .
• Refer to INSTALLING STEERING COLUMN SHROUD LOWER SECTION .
• Refer to FITTING STEERING COLUMN SHROUD UPPER SECTION .
• Refer to INSTALLING THE STEERING WHEEL (SPORTS STEERING WHEEL) .
• Refer to INSTALLING THE AIRBAG UNIT (SPORTS STEERING WHEEL) .
• Refer to INSTALLING EXPANSION VALVE .
• Refer to CONNECTING THE REFRIGERANT LINE TO THE EXPANSION VALVE .
• Refer to ATTACHING THE INTAKE PIPE BRACKET .
• Refer to INSTALLING LEFT INTAKE FILTER HOUSING WITH LEFT FRONT-END STRUT .
• Refer to INSTALLING COOLANT EXPANSION TANK .
• Refer to INSTALLING THE CONTROL UNIT BRACKET FOR CYLINDERS 5 TO 8 .
• Refer to INSTALLING CLEAN AIR PIPE, TOP .
• Refer to INSTALLING THE COVER OF THE LEFT DME CONTROL UNIT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to EVACUATING AND CHARGING CONDITIONING .
• Refer to CHECKING THE AIRBAG FOR FUNCTION .
• Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .