Overview - Camshaft Timing Chains: Notes
WARNING: This page is about a different car, the 2023 Volkswagen Atlas. However, it is still accessible from the selected car via links, so may be relevant.
- Control Housing
- Oil contact surface of sealing rings before installing
- Removing and installing (refer to SEALING FLANGE, REMOVING AND INSTALLING, TRANSMISSION SIDE ). Removing and installing camshafts (refer to CAMSHAFT, REMOVING AND INSTALLING ).
- Overview. Refer to OVERVIEW - CONTROL HOUSING .
- Check the control housing strainer for contamination before installing. Refer to OVERVIEW - CONTROL HOUSING .
- Seal
- Replace
- Oil Pump
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- 8 Nm
- Insert with Locking Fluid:D 000 600 A2
- Chain Tensioner, 50 Nm
- For the camshaft timing chain OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Camshaft Timing Chain
- Only rotate the engine with chain tensioner installed
- Seal
- Replace if damaged or leaking
- Tensioning Rail
- For the camshaft timing chain OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Camshaft Timing Chain
- Mounting Pin, 10 Nm
- For tensioning rail OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Tensioning Rail
- Chain Sprocket
- For the timing chains
- Install the camshaft adjuster with camshaft drive timing chain. Refer to CAMSHAFT ADJUSTER, REMOVING AND INSTALLING .
- Camshaft Timing Chain
- Mark the direction of rotation before removing (installation position). Refer to Mark the timing chain .
- Install the camshaft adjuster with camshaft drive timing chain. Refer to CAMSHAFT TIMING CHAIN, REMOVING AND INSTALLING .
- 60 Nm + 1
/4
(90°) additional turn
- Replace
- Exhaust Camshaft Adjuster
- Identification: 32A
- Install the camshaft adjuster with camshaft drive timing chain. Refer to CAMSHAFT TIMING CHAIN, REMOVING AND INSTALLING .
- 60 Nm + 1
/4
(90°) additional turn
- Replace
- The sensor wheel contact surface on the bolt head must be dry when installing
- To remove and install, counter-hold at camshaft using an open-end wrench (27 mm). Refer to CAMSHAFT, REMOVING AND INSTALLING .
- Intake Camshaft Adjuster
- Identification: 24E
- Install the camshaft adjuster with camshaft drive timing chain. Refer to CAMSHAFT TIMING CHAIN, REMOVING AND INSTALLING .
- 10 Nm
- Chain Tensioner with Tensioning Rail
- For the timing chain OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Timing Chain.
- Only rotate the engine with chain tensioner installed
- Drive Pinion
- Integrated in the crankshaft
- Ground down tooth faces the bearing joint = cylinder 1 TDC, installing the oil pump drive timing chain. Refer to TIMING CHAIN AND OIL PUMP DRIVE CHAIN, REMOVING AND INSTALLING .
- Pin without Collar, 10 Nm
- For guide rail OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Guide Rail
- Timing Chain
- Mark the direction of rotation before removing (installation position). Refer to Mark the timing chain .
- Install the oil pump drive timing chain. Refer to TIMING CHAIN AND OIL PUMP DRIVE CHAIN, REMOVING AND INSTALLING .
- Mounting Pin, 10 Nm
- For guide rail
- 23 Nm
- Guide Rail
- For the camshaft timing chain OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Camshaft Timing Chain
- Guide Rail
- For the timing chain OVERVIEW - CAMSHAFT TIMING CHAINS => List Item:Timing Chain
- Together with the timing chain, removing and installing. Install the oil pump drive timing chain. Refer to TIMING CHAIN AND OIL PUMP DRIVE CHAIN, REMOVING AND INSTALLING .
- High Pressure Pump Drive Chain Sprocket
- With needle bearing
- Coat the needle bearing with oil before installing