Rear Axle, Removing And Installing, Fwd

WARNING: This page is about a different car, the 2023 Volkswagen Atlas. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Tensioning Strap:T10038

Fig 1: Identifying Tensioning Strap T10038
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Torque Wrench, 40-200Nm:VAG1332A

Fig 2: Identifying Torque Wrench 1332
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Rear Axle, Removing

-- Loosen the wheel bolts.

-- Raise the vehicle.

-- Remove the wheels.

-- Disconnect and free up the right and left connector -1- from the ABS speed sensor.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Disconnect the right and left electromechanical parking brake connector -2- from the brake caliper.

-- Remove and free up the wiring harness from the retainer -arrows-.

Vehicles with Level Control System Sensor

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Disconnect the connector -1- and unclip the wire from the bracket.

-- Remove the bolts -2-.

-- Remove the Left Rear Level Control System Sensor -G76- -3- from the transverse link.

Continuation for All Vehicles

-- Remove the springs. Refer to SPRING, REMOVING AND INSTALLING .

-- Remove the clamps -1- on both sides of the vehicle.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Free up the brake lines from the bracket.

NOTE:

Do not disconnect the brake line.

-- Remove the left and right brake caliper and with the brake lines attached secure to the body. Refer to OVERVIEW - REAR BRAKES .

-- Remove the rear muffler from the exhaust system. Refer to OVERVIEW - MUFFLER - 2.0L , OVERVIEW - MUFFLER - 3.6L .

-- If equipped, remove the underbody trim panel on the trailing arm mounting bracket. Refer to COMPONENT LOCATION OVERVIEW - UNDERBODY TRIM PANELS .

-- Secure both sides of the vehicle on the hoist lifting arms using the :T10038 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Tensioning Strap:T10038

WARNING:

The vehicle could slide off the hoist if it is not secured.

-- Secure the subframe. Refer to SUBFRAME, SECURING .

-- Unclip and free up the wire -2- on the mounting bracket -1-.

Fig 3: Tighten The Bolts -arrows-

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Mark the installation position of the mounting bracket -1- on the body.

-- Remove the screws -arrows-.

-- Carefully lower the subframe with its components 30 mm maximum.

-- Remove the brake line from the clips -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

The clips will get damaged while doing this and will have to be replaced.

For better illustration, the subframe is shown from above and is removed.

The number of clips may vary.

-- Lower the subframe with attachments.

NOTE:

When lowering, ensure the brake lines and wires have sufficient clearance.

Subframe with Attachments, Installing

Install in reverse order of removal.

Tightening Specifications

Refer to SUBFRAME
Refer to OVERVIEW - TRAILING ARM
Refer to OVERVIEW - SUSPENSION STRUT, SHOCK ABSORBER, SPRING
Refer to OVERVIEW - REAR LEVEL CONTROL SYSTEM SENSOR
Wheel Bolts. Refer to the appropriate Service Information .
Bolts for brake caliper and brake rotor. Refer to OVERVIEW - REAR BRAKES .
Double clamp for exhaust pipes. Refer to OVERVIEW - MUFFLER - 2.0L , OVERVIEW - MUFFLER - 3.6L .

For vehicles with a level control system sensor, perform the basic setting using the Vehicle Diagnostic Tester.

-- Evaluate if an axle alignment is needed. Refer to NEED FOR AXLE ALIGNMENT, EVALUATING .