Valve Body Overview
WARNING: This page is about a different car, the 2009 Volkswagen Rabbit, 2008 Volkswagen Rabbit, 2007 Volkswagen Rabbit, and 2006 Volkswagen Rabbit. However, it is still accessible from the selected car via links, so may be relevant.
- Inspection Plug
- Transmission fluid level, checking and filling. Refer to TRANSMISSION FLUID LEVEL, CHECKING AND FILLING .
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Seal
- Always replace.
- Overflow Tube
- Remove in order to drain the transmission fluid.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Fluid Pan
- Removing and installing, refer to TRANSMISSION FLUID PAN .
- Bolt
- Tighten the transmission fluid pan bolts diagonally and in several steps.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Gasket
- With spacers (quantity: 8).
- Check before installing
- Replace a brittle, cracked or deformed gasket.
- Magnet
- Quantity: 2; in the depressions in the pan.
- Clean before installing the pan.
- Bolt
- For securing the valve body to the transmission.
- Quantity 12; with different lengths, refer to Figure.
- Always replace the bolts.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Quantity: 3
- For securing the transmission fluid filter to the valve body.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Fluid Filter
- Removing and installing, refer to TRANSMISSION FLUID FILTER .
- Valve Body
- Removing and installing, refer to VALVE BODY .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Input Speed Sensor -G182-
- Removing and installing, refer to Transmission Input Speed Sensor -G182- .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Output Speed Sensor -G195-
- Removing and Installing, refer to Transmission Output Speed Sensor -G195- .
- Transmission Housing
- The transmission fluid cooler is not illustrated
- Vent Cap
- Multifunction Transmission Range Switch -F125-
- Removing and installing, refer to Multifunction Transmission Range Switch -F125- .
- Adjusting, refer to Multifunction Transmission Range Switch -F125-, ADJUSTING .
- Transmission Fluid Temperature Sensor -G93-
- Integrated into the wiring harness.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Removing and installing, refer to SOLENOID VALVE AND SENSOR WIRING HARNESS .
- Wire routing, refer to WIRE ROUTING, CONNECTORS AND BRACKET ON VALVE BODY .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Sensor Wiring Harness
- With the transmission fluid temperature sensor.
- For the transmission input speed sensor and the transmission output speed sensor.
- Always replace the seal on the connector housing.
- Removing and installing, refer to SOLENOID VALVE AND SENSOR WIRING HARNESS .
- Wire routing, refer to WIRE ROUTING, CONNECTORS AND BRACKET ON VALVE BODY .
- Seal
- Always replace.
- Drain Plug
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Selector Shaft Lever
- Washer
- Nut
- Installed position: The centering collar faces the washer. See item 27.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Spring
- Piston
- Solenoid Valve Wiring Harness
- Always replace the seal on the connector housing.
- Removing and installing, refer to SOLENOID VALVE AND SENSOR WIRING HARNESS .
- Wire routing, refer to WIRE ROUTING, CONNECTORS AND BRACKET ON VALVE BODY .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .