Removal [01/2019 - 09/2022]: Procedure

1. Secure the steering wheel with the seat belt in order to prevent rotation.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   This operation is useful to prevent damage to the spiral cable.

Refer to PROCEDURE - Step 13 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 13 [03/2019 - 09/2019] , or refer to PROCEDURE - Step 13 [09/2019 - 04/2020] , or refer to PROCEDURE - Step 13 [04/2020 - 09/2022]

Refer to PROCEDURE - Step 14 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 14 [03/2019 - 09/2019] , or refer to PROCEDURE - Step 14 [09/2019 - 04/2020] , or refer to PROCEDURE - Step 14 [04/2020 - 09/2022]

1. Separate the clip (A), disengage the clip (B) from the vehicle body and separate the No. 1 steering column hole cover sub-assembly.
   NOTE:

   Do not damage the clips (A) or (B).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to PROCEDURE - Step 1 , or refer to REMOVAL [03/2019 - 09/2022]

for M20A-FKS: Refer to PROCEDURE - Step 9 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 9 [03/2019 - 09/2019] , or refer to PROCEDURE - Step 9 [09/2019 - 06/2021] , or refer to PROCEDURE - Step 9 [06/2021 - 09/2022]

for 2ZR-FAE: Refer to PROCEDURE - Step 7 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 7 [03/2019 - 09/2022]

for 2ZR-FXE: Refer to PROCEDURE - Step 7 [01/2019 - 04/2020] , or refer to PROCEDURE - Step 7 [04/2020 - 09/2022]

for M20A-FKS: Refer to PROCEDURE - Step 10 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 10 [03/2019 - 09/2019] , or refer to PROCEDURE - Step 10 [09/2019 - 06/2021] , or refer to PROCEDURE - Step 10 [06/2021 - 09/2022]

for 2ZR-FAE: Refer to PROCEDURE - Step 8 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 8 [03/2019 - 09/2022]

for 2ZR-FXE: Refer to PROCEDURE - Step 8 [01/2019 - 04/2020] , or refer to PROCEDURE - Step 8 [04/2020 - 09/2022]

for M20A-FKS: Refer to PROCEDURE - Step 11 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 11 [03/2019 - 09/2019] , or refer to PROCEDURE - Step 11 [09/2019 - 06/2021] , or refer to PROCEDURE - Step 11 [06/2021 - 09/2022]

for 2ZR-FAE: Refer to PROCEDURE - Step 9 [01/2019 - 03/2019] , or refer to PROCEDURE - Step 9 [03/2019 - 09/2022]

for 2ZR-FXE: Refer to PROCEDURE - Step 9 [01/2019 - 04/2020] , or refer to PROCEDURE - Step 9 [04/2020 - 09/2022]

Refer to PROCEDURE - Step 10

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 12

HINT: 

Perform the same procedure as for the LH side.

1. Remove the cotter pin and nut.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install SST to the tie rod end sub-assembly LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09960-20010 
     1. 09961-02060
   NOTE:

   Make sure that the upper ends of the tie rod end sub-assembly LH and SST are aligned.

3. Secure SST using a string.
   NOTE:

   Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

4. Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.
   • SST: 09960-20010 
     1. 09961-02010

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	String	*b	Molybdenum Grease Application Area
   *c	Place wrench here	*d	Center Nut
   	Turn	-	-

   WARNING:

   Apply molybdenum grease to the bolt threads and the tip of SST.

   NOTE:

   • Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.
   • Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.
   • Be sure to place the wrench on the part shown in the illustration.
   • Do not damage the front disc brake dust cover.
   • Do not damage the ball joint dust cover.
   • Do not damage the steering knuckle LH.

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 9

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 18

1. Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.

1. Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   NOTE:

   Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

1. Using SST, secure the steering link assembly in a vise.
   • SST: 09612-00012 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Protective Tape

   HINT: 

   Wrap SST with protective tape before use.

1. Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Matchmark

2. Remove the tie rod end sub-assembly LH and lock nut.

HINT: 

Perform the same procedure as for the LH side.