Installation [06/2017 - ]: Procedure

INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Check that the ignition switch is off.

Check that the cable is disconnected from the negative (-) battery terminal.

WARNING:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Airbag Connector
*b	Airbag Connector Locking Button
	Push in this Direction

NOTE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

Push in the airbag connector locking button to install the airbag connector.

Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

Engage the 2 claws.
Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTE:
Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Refer to PROCEDURE - Step 10 [06/2017 - 09/2019] , or refer to PROCEDURE - Step 9 [09/2019 - 03/2020] , or refer to PROCEDURE - Step 9 [03/2020 - ]
INSTALL NO. 1 METER HOOD CLUSTER
Refer to PROCEDURE - Step 13 [06/2017 - 09/2019] , or refer to PROCEDURE - Step 12 [09/2019 - 03/2020] , or refer to PROCEDURE - Step 12 [03/2020 - ]
INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 25 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 28 [10/2020 - ]
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 26 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 29 [10/2020 - ]
INSTALL NO. 2 METER HOOD CLUSTER
Refer to PROCEDURE - Step 27 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 30 [10/2020 - ]
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 28 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 31 [10/2020 - ]
INSTALL INSTRUMENT SIDE PANEL LH
Refer to PROCEDURE - Step 29 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 32 [10/2020 - ]
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Refer to PROCEDURE - Step 30 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 30 [08/2018 - 09/2019] , or refer to PROCEDURE - Step 27 [09/2019 - 03/2020] , or refer to PROCEDURE - Step 27 [03/2020 - 08/2021] , or refer to PROCEDURE - Step 27 [08/2021 - ]
INSTALL FRONT DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 31 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 31 [08/2018 - 09/2019] , or refer to PROCEDURE - Step 28 [09/2019 - 03/2020] , or refer to PROCEDURE - Step 28 [03/2020 - 08/2021] , or refer to PROCEDURE - Step 28 [08/2021 - ]
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
For A25A-FKS: Refer to PROCEDURE - Step 2 [03/2017 - 08/2018] , or refer to PROCEDURE - Step 2 [08/2018 - ]

For 2GR-FKS: Refer to PROCEDURE - Step 2

NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Refer to INITIALIZATION [06/2017 - 08/2018] , or refer to INITIALIZATION [08/2018 - 09/2019] , or refer to INITIALIZATION [09/2019 - 03/2020] , or refer to INITIALIZATION [03/2020 - 10/2020] , or refer to INITIALIZATION [10/2020 - 08/2022] , or refer to INITIALIZATION [08/2022 - ]
PERFORM DIAGNOSTIC SYSTEM CHECK
Refer to DTC CHECK / CLEAR [03/2017 - ]
INSPECT SRS WARNING LIGHT
Refer to OPERATION CHECK [06/2017 - 09/2019] , or refer to OPERATION CHECK [09/2019 - 10/2020] , or refer to OPERATION CHECK [10/2020 - 08/2022] , or refer to OPERATION CHECK [08/2022 - ]