LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Highlander L, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 24 (Engine Mechanical System (T24A-FTS) - Service Information (1 Of 2)) >> Camshaft >> Removal [11/2023 - ] >> Procedure

Removal [11/2023 - ]: Procedure

WARNING: This page is about a different car, the 2025 Toyota Highlander, 2024 Toyota Highlander, and 2023 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND 

    Refer to REMOVAL [11/2023 - ] 

  2. REMOVE ENGINE HANGERS 
  3. REMOVE NO. 2 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 4

  4. REMOVE PURGE VALVE (PURGE VSV) 

    Refer to PROCEDURE - Step 17

  5. DISCONNECT NO. 1 VENTILATION PRESSURE SENSOR HOSE 

    Refer to PROCEDURE - Step 4

  6. REMOVE AIR TUBE ASSEMBLY 

    Refer to PROCEDURE - Step 8

  7. DISCONNECT NO. 2 FUEL VAPOR FEED HOSE 

    Refer to PROCEDURE - Step 10

  8. REMOVE VACUUM REGULATING VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 21

  9. REMOVE COMPRESSOR INLET ELBOW SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 22

  10. DISCONNECT NO. 2 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 26

  11. DISCONNECT NO. 3 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 27

  12. DISCONNECT WATER OUTLET STAY 

    Refer to PROCEDURE - Step 28

  13. DISCONNECT FUEL TUBE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  14. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 11

  15. REMOVE FUEL PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 12

  16. REMOVE FUEL PUMP SPACER GASKET 

    Refer to PROCEDURE - Step 13

  17. REMOVE FUEL PUMP LIFTER ASSEMBLY 

    Refer to PROCEDURE - Step 14

  18. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 3

  19. REMOVE EXHAUST PIPE HEAT INSULATOR 

    Refer to PROCEDURE - Step 2

  20. REMOVE WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 45

  21. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 46

  22. REMOVE WATER BY-PASS GASKET 

    Refer to PROCEDURE - Step 47

  23. REMOVE NO. 1 HEAT INSULATOR BRACKET 

    Refer to PROCEDURE - Step 28

  24. REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 3

  25. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side) 

    Refer to PROCEDURE - Step 2

  26. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side) 

    Refer to PROCEDURE - Step 3

  27. REMOVE CAM TIMING OIL CONTROL SOLENOID O-RING 

    Refer to PROCEDURE - Step 4

  28. REMOVE VACUUM PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 6

  29. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  30. REMOVE DIRECT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 4

  31. REMOVE NOZZLE HOLDER CLAMP 

    Refer to PROCEDURE - Step 5

  32. REMOVE NO. 3 FUEL INJECTOR BACK-UP RING 

    Refer to PROCEDURE - Step 6

  33. REMOVE NO. 1 FUEL INJECTOR BACK-UP RING 

    Refer to PROCEDURE - Step 7

  34. REMOVE C-RING 

    Refer to PROCEDURE - Step 8

  35. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 9

  36. REMOVE FUEL INJECTOR SEAL 

    Refer to PROCEDURE - Step 10

  37. REMOVE CRANKSHAFT PULLEY ASSEMBLY 

    Refer to PROCEDURE - Step 22

  38. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side) 

    Refer to PROCEDURE - Step 2

  39. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side) 

    Refer to PROCEDURE - Step 3

  40. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25

  41. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 26

  42. REMOVE INJECTOR HOLDER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 27

  43. REMOVE ENGINE MOUNTING BRACKET RH 

    Refer to PROCEDURE - Step 28

  44. REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 30

  45. REMOVE TIMING CHAIN CASE OIL SEAL 

    Refer to PROCEDURE - Step 31

  46. SET NO. 1 CYLINDER TO TDC (COMPRESSION) 

    Refer to PROCEDURE - Step 32

  47. REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 33

  48. REMOVE NO. 2 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 34

  49. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 35

  50. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 36

  51. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 37

  52. REMOVE NO. 1 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 38

  53. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 39

  54. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 

    Refer to PROCEDURE - Step 40

  55. REMOVE TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 41

  56. REMOVE FUEL PUMP LIFTER GUIDE 

    Refer to PROCEDURE - Step 43

  57. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 44

  58. REMOVE CAMSHAFT BEARING CAP 

    Refer to PROCEDURE - Step 45

  59. REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY 
    1. GTY1076912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  60. REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY 
    1. GTY1076913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  61. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 48

  62. REMOVE VALVE LASH ADJUSTER ASSEMBLY 

    Refer to PROCEDURE - Step 49

  63. REMOVE VALVE STEM CAP 

    Refer to PROCEDURE - Step 50

scientia non olet · About LEMON Manuals