LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Engine Mechanical System (2GR-FKS) - Service Information (1 Of 3) (Except Hybrid)) >> Cylinder Head Gasket >> Removal [06/2017 - 08/2018] >> Procedure

Removal [06/2017 - 08/2018]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND 

    Refer to REMOVAL [06/2017 - 08/2018]

  2. REMOVE ENGINE HANGERS 

    Refer to PROCEDURE - Step 60

  3. REMOVE KNOCK CONTROL SENSOR 

    Refer to REMOVAL [06/2017 - 10/2020]

  4. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  5. REMOVE VACUUM PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 5

  6. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 3

  7. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 6

  8. REMOVE COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH 

    Refer to PROCEDURE - Step 6

  9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 14

  11. REMOVE WATER PUMP PULLEY 

    Refer to PROCEDURE - Step 4

  12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 

    Refer to PROCEDURE - Step 16

  13. REMOVE WIRE HARNESS CLAMP BRACKET 

    Refer to PROCEDURE - Step 18

  14. REMOVE WATER FILLER BRACKET 

    Refer to PROCEDURE - Step 19

  15. REMOVE CRANKSHAFT PULLEY 

    See step  3

  16. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH 

    Refer to PROCEDURE - Step 7

  17. DISCONNECT WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 13

  18. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 14

  19. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) 

    Refer to PROCEDURE - Step 3

  20. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1) 

    Refer to PROCEDURE - Step 5

  21. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2) 

    Refer to PROCEDURE - Step 2

  22. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2) 

    Refer to PROCEDURE - Step 7

  23. REMOVE VVT SENSOR (for Intake Side of Bank 1) 

    Refer to PROCEDURE - Step 2

  24. REMOVE VVT SENSOR (for Exhaust Side of Bank 1) 

    Refer to PROCEDURE - Step 3

  25. REMOVE VVT SENSOR (for Intake Side of Bank 2) 

    Refer to PROCEDURE - Step 4

  26. REMOVE VVT SENSOR (for Exhaust Side of Bank 2) 

    Refer to PROCEDURE - Step 5

  27. REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR 

    Refer to PROCEDURE - Step 2

  28. REMOVE SENSOR WIRE 

    Refer to PROCEDURE - Step 62

  29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 22

  30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 23

  31. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 24

  32. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 28

  33. REMOVE OIL STRAINER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 29

  34. REMOVE OIL PAN SUB-ASSEMBLY 
    1. Remove the 16 bolts and 2 nuts from the oil pan sub-assembly.
      GTY635438Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Nut
      NOTE:

      Make sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

    2. Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and timing chain cover assembly or cylinder block sub-assembly with a screwdriver wrapped with protective tape.
      GTY645654Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder block sub-assembly, timing chain cover assembly and oil pan sub-assembly.

    3. Remove the 2 oil pan gaskets from the timing chain cover assembly.
      GTY653367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE TIMING CHAIN COVER ASSEMBLY 

    Refer to PROCEDURE - Step 3

  36. REMOVE TIMING CHAIN CASE OIL SEAL 

    See step  4

  37. SET NO. 1 CYLINDER TO TDC (COMPRESSION) 

    Refer to PROCEDURE - Step 38

  38. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 39

  39. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 40

  40. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 41

  41. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) 

    Refer to PROCEDURE - Step 47

  42. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 48

  43. REMOVE CAMSHAFT BEARING CAP (for Bank 1) 

    Refer to PROCEDURE - Step 49

  44. REMOVE CAMSHAFT 

    Refer to PROCEDURE - Step 50

  45. REMOVE NO. 2 CAMSHAFT 

    Refer to PROCEDURE - Step 51

  46. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 52

  47. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) 

    Refer to PROCEDURE - Step 53

  48. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 54

  49. REMOVE CAMSHAFT BEARING CAP (for Bank 2) 

    Refer to PROCEDURE - Step 55

  50. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 56

  51. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 57

  52. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 58

  53. REMOVE SENSOR WIRE 

    Refer to PROCEDURE - Step 2

  54. REMOVE NO. 1 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 43

  55. REMOVE NO. 2 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 44

  56. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 59

  57. REMOVE VALVE LASH ADJUSTER ASSEMBLY 

    Refer to PROCEDURE - Step 60

  58. REMOVE VALVE STEM CAP 

    Refer to PROCEDURE - Step 61

  59. REMOVE WATER OUTLET 

    Refer to PROCEDURE - Step 21

  60. REMOVE CYLINDER HEAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 65

  61. REMOVE CYLINDER HEAD GASKET 
    1. Remove the cylinder head gasket from the cylinder block sub-assembly.
  62. REMOVE CYLINDER HEAD LH 

    Refer to PROCEDURE - Step 67

  63. REMOVE NO. 2 CYLINDER HEAD GASKET 
    1. Remove the No. 2 cylinder head gasket from the cylinder block sub-assembly.
  64. INSPECT CYLINDER HEAD SET BOLT 

    Refer to PROCEDURE - Step 4

scientia non olet · About LEMON Manuals