LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seats (Service Information) (Except Hybrid) (1 Of 2) >> Front Seat Assembly (For Manual Seat) >> Reassembly [11/2016 - ] >> Procedure

Reassembly [11/2016 - ]: Procedure

  1. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY 
    1. Engage 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
      GTY728085Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL SEAT ADJUSTER COVER CAP 
    1. Install the 2 seat adjuster cover caps.
      GTY424570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL NO. 1 SEAT WIRE (w/ Seat Heater System) 
    1. Engage each claw and each clamp to install the No. 1 seat wire.
  4. INSTALL FRONT SEAT WIRE (for Front Passenger Side) 
    1. Engage each claw and each clamp to install the front seat wire.
  5. INSTALL SEAT TRACK ADJUSTING HANDLE 
    1. Engage the 2 springs to install the seat track adjusting handle.
      GTY424556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side) 
    1. Engage the 3 claws and guide to install the LH seat front seat cushion edge protector LH.
      GTY424554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSTALL LH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side) 

    HINT: 

    Use the same procedure as for the LH side.

  8. INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side) 
    1. Engage the 3 claws and guide to install the RH seat front seat cushion edge protector LH.
      GTY424557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSTALL RH SEAT FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side) 

    HINT: 

    Use the same procedure as for the LH side.

  10. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side) 
    1. Engage the clip to install the front seat lower cushion shield LH.
      GTY424555Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the hook as shown in the illustration.
    3. Install the screw.
  11. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side) 

    HINT: 

    Use the same procedure as for the LH side.

  12. INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY RH (for Front Passenger Side) 

    Refer to PROCEDURE - Step 1

  13. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) 

    Refer to PROCEDURE - Step 1

  14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER 
    1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
      GTY447867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the separate type front seat cushion cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
    2. Using hog ring pliers, install 2 new hog rings.
      GTY455610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the separate type front seat cushion cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
  15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Driver Side) 
    1. Engage the 13 hooks to install the separate type front seat cushion cover with pad.
      GTY424549Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Front Passenger Side) 
    1. Engage the 11 hooks to install the separate type front seat cushion cover with pad.
      GTY424550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/ Seat Heater System:
      1. Engage the 3 clamps.
        GTY423579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. INSTALL FRONT SEATBACK HOOK 
    1. Install the 2 front seatback hooks to the front seatback spring sub-assembly.
  18. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY 
    1. Engage the 2 guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.
      GTY728086Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the 2 claws.
  19. INSTALL FRONT SEATBACK EDGE PROTECTOR 
    1. Engage each claw to install the 2 front seatback edge protectors.
      GTY449496Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. INSTALL FRONT SEAT AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 1

  21. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) 

    Refer to PROCEDURE - Step 1

  22. INSTALL SEPARATE TYPE FRONT SEATBACK COVER 
    1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.
      GTY429679Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the separate type front seatback cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
    2. GTY429702Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using hog ring pliers, install 4 new hog rings.

      NOTE:
      • Be careful not to damage the separate type front seatback cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
  23. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD 
    1. Install the separate type front seatback cover with pad.
  24. INSTALL FRONT SEAT HEADREST SUPPORT ASSEMBLY 
    1. GTY429714Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Engage each claw to install the 2 front seat headrest support assemblies.

    2. Engage the 3 brackets and install the 2 nuts.
      GTY446888Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Bracket

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      NOTE:
      • For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
      • Make sure that the strap is not twisted after installing the nut.
      • Install the brackets securely.
    3. GTY429717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Return the separate type front seatback cover to its original position.

    4. GTY455611Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using hog ring pliers, install 2 new hog rings.

      NOTE:
      • Be careful not to damage the separate type front seatback cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
    5. GTY429719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using hog ring pliers, install 3 new hog rings.

      NOTE:
      • Be careful not to damage the separate type front seatback cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
    6. GTY427299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using hog ring pliers, install 7 new hog rings.

      NOTE:
      • Be careful not to damage the separate type front seatback cover.
      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
  25. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY 
    1. Engage the 4 guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
      GTY424553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 4 bolts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    3. w/ Seat Heater System:
      1. Engage the clamp.
        GTY423577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Connect the connector.
    4. Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
      GTY426850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Seat Clamp
    5. Install the front seat airbag assembly wire harness to the seat clamp.
    6. Engage the fastener to secure the front seat airbag assembly wire harness.
      GTY450322Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fastener
    7. Engage the 2 hooks.
      GTY424552Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side) 

    Refer to PROCEDURE - Step 1

  27. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) 

    Refer to PROCEDURE - Step 1

  28. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) 

    Refer to PROCEDURE - Step 2

  29. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side) 
    1. Engage the claw and guide to install the front seat inner cushion shield.
      GTY424561Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the claw and 3 guides.
      GTY424560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side) 
    1. Engage the claw and guide to install the front seat inner cushion shield.
      GTY450567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the claw and 4 guides.
      GTY424566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side) 
    1. Engage the claw, guide and 2 clips to install the front seat cushion shield.
      GTY424562Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the claw and 3 guides.
      GTY450566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side) 
    1. Engage the claw, guide and 2 clips to install the front seat cushion shield.
      GTY424567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the claw and 4 guides.
      GTY424559Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side) 
    1. Install the vertical adjusting handle with the screw.
      GTY424564Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. INSTALL RECLINING ADJUSTER RELEASE HANDLE 
    1. Engage the claw to install the reclining adjuster release handle.
      GTY450349Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. CONNECT SEPARATE TYPE FRONT SEATBACK COVER 
    1. GTY450552Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Connect the rubber band of the separate type front seatback cover.

  36. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System) 

    Refer to PROCEDURE - Step 1

  37. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side) 

    Refer to PROCEDURE - Step 1

scientia non olet · About LEMON Manuals