Retrofit COMAND Online - AN82.85-P-0009LWB

Model 205.0/2/3/4

with code 3U1 (Head unit europe/CIS-states/Monoglei)

with code 506 (Audio 20 NTG 5.5 radio)

except code 448 (Touchpad)

except code 520 (Audio 20 USB)

except code 522 (Audio 20 radio)

except code 625 (Australia specification)

except code 822 (Addit. parts for South African vehicles)

except code 830 (China version)

except code 835 (South Korea version)

Courtesy of MERCEDES-BENZ USA

Courtesy of MERCEDES-BENZ USA

	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove
1	Remove head unit (A26/17).
		The head unit (A26/17) is no longer required.	AR82.85-P-1101LWM
2	Remove audio/COMAND display (A40/8).	Model 205.0/2/3/4 except code 859 (Central display)
		The Audio/COMAND display (A40/8) is no longer required.	AR82.60-P-7722LW
3	Remove Audio/COMAND control panel (A40/9).
		The Audio/COMAND control panel (A40/9) is no longer required.	AR54.21-P-0500LW
4	Loosen rear floor covering (1) on the left side and fold to the side until the cable duct (2) is accessible.
		Do not remove seat cushion in the rear.	AR68.20-P-4800LW
5	Open cable duct (2) until the head unit CAN (low) end sleeve (Z35/32z1) and the head unit CAN (high) end sleeve (Z35/31z1) are accessible.
	Install
	Risk of injury caused by burns to skin and eyes, risk of poisoning caused by inhaling fumes during soldering.	Wear protective gloves, protective clothing and safety glasses. Ensure that the work area is adequately ventilated. Secure power supply cables. Avoid sources of fire in working area.	AS00.19-Z-0002-01A
6	Retrofit CAN wiring harness. Notes on soft soldering		AH00.19-P-1000-07A
	Location of end sleeves - Center console	Model 205.0/2/3/4 as of model year 2019	GF00.19-P-3005-11FBA
	Repairing wiring harness using solder connectors		AR00.19-P-0100-09A
			AN82.60-P-0017-02LWA
		Adhesive fabric tape	*BR00.45-Z-1062-02A
		Wire stripper	Fig 5
		Reflector	Fig 6
		Adapter	Fig 3
		Welding bead catcher	Fig 1
		New passenger car wiring harness repair kit	Fig 2
		Wiring harness repair kit, basic	Fig 4
7	Retrofit touchpad (A105).		AN82.60-P-0017-03LW
8	Retrofit wiring harness for touchpad.		AN82.60-P-0017-01LW
9	Install new Audio/COMAND control panel (A40/9).
		Install Audio/COMAND control panel (A40/9) into center console cover.	AR54.21-P-0500LW
10	Close cable duct (2).
11	Fix rear floor covering (1) in place.
			AR68.20-P-4800LW
12	Install new audio/COMAND display (A40/8).	Model 205.0/2/3/4 except code 859 (Central display)
			AR82.60-P-7722LW
13	Install new head unit (A26/17).
			AR82.85-P-1101LWM
	Update Vehicle Documentation (VeDoc)
14	Delete special equipment from on-line vehicle data card.	Code 506 (Audio 20 radio NTG 5.5) Model 205.0/2/3/4 with code 355 (Preinstallation for navigation retrofit) Model 205.0/2/3/4 with code 357 (Map navigation)
15	Enter special equipment into online vehicle data card.	Code 01U (Navigation service) Code 02U (Office function in vehicle) Code 08U (Vehicle setup) Code 09U (Vehicle monitoring) Code 12U (Concierge service) Code 15U (Pre-installation for Mercedes-Benz Link) Code 448 (Touchpad) Code 531 (COMAND APS) Model 205.0/2/3/4 except code 859 (Central display) Code 859 (Central display)
16	Attach note "COMAND Online retrofitted as per " under field organization texts to DG 54 and DG 82.		AN82.85-P-0009LWB
17	Connect diagnostic system and select vehicle using vehicle identification number (VIN).
			AD00.00-P-2000-04B
18	Perform variant coding for retrofitting of special equipment.		AN82.61-P-0001-05LW
19	Disconnect diagnostic system.
			AD00.00-P-2000-04B
	Check
20	Perform function test.	See Owner's Manual.