Retrofit anti-theft-alarm system (ATA) with towing sensor (TS) - AN80.50-P-0002A
MODEL 210 as of 1.3.97
| Remove | |||
| 1 | Remove front seats | ||
| AR91.10-P-1000F | |||
| 2 | Remove rear seat and rear backrest | Models 210.0/6 | |
| AR91.12-P-1700F | |||
| 3 | Remove rear seat cushion | Model 210.2 | |
| 4 | Disconnect ground cable of battery | ||
| AR54.10-P-0003A | |||
| 5 | Remove fuse box in rear passenger compartment and place to one side | ||
| 6 | Remove pneumatic system equipment | ||
| AR80.20-P-2700F | |||
| 7 | Remove center console | ||
| AR68.20-P-2000F | |||
| 8 | Remove cover on center console | ||
| AR68.20-P-2350F | |||
| 9 | Remove cover below instrument panel (left) | ||
| AR68.10-P-1500F | |||
| 10 | Remove front floor covering (left) | ||
| AR68.20-P-2050F | |||
| 11 | Remove hot-air outlets of rear footwell at left and right | ||
| 12 | Remove rear floor covering | ||
| 13 | Open cable ducts on vehicle floor | ||
| 14 | Remove fuse blocks, control modules and relays from the fuse and relay box | ||
| AR54.15-P-1255EB | |||
| 15 | Expose passage of fuse and relay box to the driver's footwell | ||
| 16 | Remove control module box | ||
| AR54.20-P-1257A | |||
| 17 | Remove air cleaner | ||
| AR09.10-P-1050C | |||
| 18 | Remove washing water tank for washer system and headlamp cleaning system | ||
| 19 | Remove right front wheel | ||
| 20 | Remove right front fender skirt at rear of wheel house | ||
| Install | |||
| 21 | Cut opening for switch in covering | ||
| AR68.20-P-2030A | |||
| 22 | Line up the ATA interior/towing/status indicator switch (S85/2) to match the opening in the covering and clip it into the switch strip | ||
| 23 | Install the PSE control module | ||
| AR80.20-P-2700F | |||
| 24 | Retrofit wiring harness Models 210.0/6 | AN80.50-P-0001-01A | |
| Model 210.2 | AN80.50-P-0001-01B | ||
| 25 | Retrofit the engine hood switch | AN80.50-P-0001-04A | |
| 26 | Retrofit alarm siren | AN80.50-P-0001-02A | |
| Preservation agent | *BR00.45-Z-1003-05A | ||
| 27 | Retrofit inclination sensor | AN80.50-P-0001-05A | |
| 28 | Fit remaining parts to vehicle | ||
| 29 | Conduct control unit coding for the pneumatic system equipment using the HHT | ||
| 30 | Check functionality of antitheft alarm system with towing sensor | ||
| 31 | Amend special equipment code 551 in FDOK |
Repair materials
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1003-05A | Preservation agent | A 000 986 72 70 05 |
Parts ordering notes
| Part no. | Designation | Quantity |
|---|---|---|
| Group 82 | ATA/TS/IMS wiring harness | 1 |
| Group 82 | ATA [EDW] inclination sensor | 1 |
| Group 82 | Alarm signal horn with additional battery | 1 |
| Group 82 | Bracket for alarm signal siren | 1 |
| Group 82 | ATA [EDW] hood switch | 1 |
| Group 82 | ATA [EDW] interior/towing/status indicator switch | 1 |
| Group 80 | PSE control module (combined) | 1 |