Section 213 (Engine Mechanical - 2.0L (LTG) - Repair Instructions - Off Vehicle)
WARNING: This page is about a different car, the 2017 Cadillac ATS. However, it is still accessible from the selected car via links, so may be relevant.
- Repair Instructions - Off Vehicle
- Draining Fluids and Oil Filter Removal
- Crankshaft Balancer Removal
- Engine Flywheel Removal
- Automatic Transmission Flex Plate Removal
- Intake Manifold Removal
- Turbocharger Removal
- Exhaust Manifold Removal (LTG)
- Exhaust Manifold Removal (LCV)
- Fuel Rail and Injectors Removal
- Camshaft Cover Removal (LCV)
- Camshaft Cover Removal (LTG)
- Engine Front Cover Removal
- Camshaft Timing Chain and Tensioner Removal
- Oil Pan Removal (LCV)
- Oil Pan Removal (LTG)
- Balancer Chain, Sprocket, and Tensioner Removal
- Intake and Exhaust Camshaft, Bearing Cap, and Lash Adjuster Removal
- Water Pump Removal (LCV)
- Water Pump Removal (LTG)
- Cylinder Head Removal
- Balancer Shaft with Oil Pump Removal
- Piston, Connecting Rod, and Bearing Removal
- Lower Crankcase Removal
- Crankshaft and Bearing Removal
- Engine Block Disassemble
- Engine Block Cleaning and Inspection
- Crankshaft Balancer Cleaning and Inspection
- Engine Flywheel Cleaning and Inspection
- Automatic Transmission Flex Plate Cleaning and Inspection
- Crankshaft and Bearing Cleaning and Inspection
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearing Cleaning and Inspection
- Piston and Connecting Rod Assemble
- Camshaft Assembly Disassemble
- Camshaft Cleaning and Inspection
- Camshaft Assembly Assemble
- Camshaft Timing Chain, Sprocket, and Tensioner Cleaning and Inspection
- Cylinder Head Disassemble
- Cylinder Head Cleaning and Inspection
- Valve and Seat Grinding
- Valve Measurement and Reconditioning Overview
- Valve Seat Width Measurement Procedure
- Valve Seat Roundness Measurement Procedure
- Valve Head O.D. and Chamfer Measurement Procedure
- Valve-to-Seat Concentricity Measurement Procedure
- Valve and Seat Reconditioning Procedure
- Valve Stem Height Measurement Procedure
- Cylinder Head Assemble
- Balancer Shaft with Oil Pump Disassemble
- Balancer Shaft with Oil Pump Cleaning and Inspection
- Balancer Shaft with Oil Pump Assemble
- Camshaft Cover Cleaning and Inspection (LCV)
- Camshaft Cover Cleaning and Inspection (LTG)
- Turbocharger Cleaning and Inspection
- Fuel Rail and Injectors Cleaning and Inspection
- Intake Manifold Cleaning and Inspection
- Exhaust Manifold Cleaning and Inspection
- Oil Pan Cleaning and Inspection
- Thread Repair
- Service Prior to Assembly
- Engine Block Assemble
- Crankshaft and Bearing Installation
- Lower Crankcase Installation
- Piston, Connecting Rod, and Bearing Installation (LTG)
- Piston, Connecting Rod, and Bearing Installation (LCV)
- Balancer Shaft with Oil Pump Installation
- Cylinder Head Installation
- Water Pump Installation (LCV)
- Water Pump Installation (LTG)
- Intake and Exhaust Camshaft, Bearing Cap, and Lash Adjuster Installation
- Balancer Chain, Sprocket, and Tensioner Installation
- Oil Pan Installation (LCV)
- Oil Pan Installation (LTG)
- Camshaft Timing Chain and Tensioner Installation
- Engine Front Cover Installation
- Camshaft Cover Installation (LCV)
- Camshaft Cover Installation (LTG)
- Fuel Rail and Injectors Installation
- Exhaust Manifold Installation (LTG)
- Exhaust Manifold Installation (LCV)
- Intake Manifold Installation
- Turbocharger Installation
- Engine Flywheel Installation
- Automatic Transmission Flex Plate Installation
- Crankshaft Balancer Installation
- Oil Filter Installation
- Engine Prelubing