DTC Chart: TCM

WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC Chart

DTC	Description	Component	Action
P0604	Internal Control Module Random Access Memory (RAM) Error	TCM	REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. If DTCs return, INSTALL a new TCM. REFER to: TRANSMISSION CONTROL MODULE (TCM) After installing the new TCM PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle .
P0605	Internal Control Module Read Only Memory (ROM) Error	TCM	REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle .
P0607	Control Module Performance	TCM	REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle .
P064F	Control module calibration	TCM	REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. If the DTC returns, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle .
P0657	Actuator Supply Voltage A Circuit Open	TCM	Power is routed through the Transmission Solenoid Power Control (TSPC) relay (inside the TCM) to all solenoids. If the power circuit to the transmission solenoids or the TSPC relay fails open, then all solenoids are failed electrically off. CHECK for open, short to ground or the transmission connector disconnected. The TSPC relay also disables power to the transmission solenoids when certain transmission DTCs are set. REPAIR as required. CLEAR the DTC. GO to Pinpoint Test A
P06B8	Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error	TCM	REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle .
P0701	Transmission Control System Range/Performance	TCM	Intermittent clutch on fault and may set with DTCs P2700, P2701, P2702, P2703 and/or P2704. CLEAR the DTC. If DTC P0701 returns, REFER to: Diagnosis By Symptom .
P0702	Transmission Control System Electrical	TCM	INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and (KOER self-test. If DTC P0702 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P0706	Transmission Range Sensor "A" Circuit Range/Performance	TR sensor	The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank. CLEAR the DTC. If DTC P0706 returns, GO to Pinpoint Test C
P0707	Transmission Range Sensor "A" Circuit Low	TR sensor	Engine may not crank, CLEAR the DTC. If DTC P0707 returns, GO to Pinpoint Test C
P0708	Transmission Range Sensor "A" Circuit High	TR sensor	Engine may not crank, CLEAR the DTC. If DTC P0708 returns, GO to Pinpoint Test C
P0710	Transmission Fluid Temperature Sensor "A" Circuit	TFT sensor	CLEAR the DTC. If DTC P0710 returns, GO to Pinpoint Test B
P0711	Transmission Fluid Temperature Sensor "A" Circuit Range/Performance	TFT sensor	CLEAR the DTC. If DTC P0711 returns, GO to Pinpoint Test B
P0712	Transmission Fluid Temperature Sensor "A" Circuit Low	TFT sensor	DTC P0710 may set. CLEAR the DTC. If DTC P0712 returns, GO to Pinpoint Test B
P0713	Transmission Fluid Temperature Sensor "A" Circuit High	TFT sensor	DTC P0710 may set. CLEAR the DTC. If DTC P0713 returns, GO to Pinpoint Test B
P0715	Turbine/Input Shaft Speed Sensor "A" Circuit	TSS sensor	DTC P0717 may set. CLEAR the DTC. If DTC P0715 returns, GO to Pinpoint Test D
P0717	Turbine/Input Shaft Speed Sensor "A" Circuit No Signal	TSS sensor	This DTC sets when DTC P0715 is set. REFER to DTC P0715.
P0718	Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent	TSS sensor	CLEAR the DTC. If DTC P0718 returns, GO to Pinpoint Test D
P0720	Output Shaft Speed Sensor Circuit	OSS sensor	DTC P0722 may set. CLEAR the DTC. If DTC P0720 returns, GO to Pinpoint Test E
P0721	Output Shaft Speed Sensor Circuit Range/Performance	OSS sensor	CLEAR the DTC. If DTC P0721 returns, GO to Pinpoint Test E
P0722	Output Shaft Speed Sensor Circuit No Signal	OSS sensor	This DTC sets when DTC P0720 is set. REFER to DTC P0720.
P0729	Gear 6 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0729 returns, REFER to: Diagnosis By Symptom .
P0731	Gear 1 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0731 returns, REFER to: Diagnosis By Symptom .
P0732	Gear 2 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0732 returns, REFER to: Diagnosis By Symptom .
P0733	Gear 3 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0733 returns, REFER to: Diagnosis By Symptom .
P073D	Unable To Engage Neutral	Transmission internal	PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. If the DTC returns, check the transmission for internal failure. REFER to the appropriate procedure in the Transmission information
P0734	Gear 4 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0734 returns, REFER to: Diagnosis By Symptom .
P0735	Gear 5 Incorrect Ratio	Transmission	CLEAR the DTC. If DTC P0735 returns, REFER to: Diagnosis By Symptom .
P0740	Torque Converter Clutch Solenoid Circuit/Open	TCC solenoid	TCC open circuit. DTC P0743 may set, CLEAR the DTC. If DTC P0740 returns, GO to Pinpoint Test A
P0741	Torque Converter Clutch Solenoid Performance/Stuck Off	TCC non-electrical fault	The torque converter clutch did not apply when TCC was commanded on. DTC P1744 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0741 returns, REFER to: Diagnosis By Symptom .
P0742	Torque Converter Clutch Solenoid Circuit Stuck On	TCC solenoid	TCC solenoid short to ground. DTC P0743 may set, CLEAR the DTC. If DTC P0742 returns, GO to Pinpoint Test A
P0743	Torque Converter Clutch Solenoid Circuit Electrical	TCC solenoid	TCC electrical circuit fault. DTC P0740, P0742 and/or P0744 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0744	Torque Converter Clutch Solenoid Circuit Intermittent	TCC solenoid	TCC short to power. DTC P0743 may set, CLEAR the DTC. If DTC P0744 returns, GO to Pinpoint Test A
P0748	Pressure Control Solenoid Electrical	LPC solenoid	LPC solenoid electrical circuit fault. DTC P0760, P0762 and/or P0763 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0750	Shift Solenoid "A"	SSA	SSA open circuit. DTC P0753 may set, CLEAR the DTC. If DTC P0750 returns, GO to Pinpoint Test A
P0751	Shift Solenoid "A" Performance/Stuck Off	SSA non-electrical fault	The forward clutch did not apply when SSA was commanded on. DTC P2700 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0751 returns, REFER to: Diagnosis By Symptom .
P0752	Shift Solenoid "A" Stuck On	SSA non-electrical fault	The forward clutch did not release when SSA was commanded off. DTC P2700 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0752 returns, REFER to: Diagnosis By Symptom .
P0753	Shift Solenoid "A" Electrical	SSA	SSA electrical circuit fault. DTC P0750, P0973 and/or P0974 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0754	Shift Solenoid "A" Intermittent	SSA	Intermittent circuit fault on SSA. CLEAR the DTC. Monitor SSPCA_F PID while wiggle testing the harness or road testing the vehicle. If DTC P0754 returns, GO to Pinpoint Test A
P0755	Shift Solenoid "B"	SSB	SSB open circuit. DTC P0758 may set, CLEAR the DTC. If DTC P0755 returns, GO to Pinpoint Test A
P0756	Shift Solenoid "B" Performance/Stuck Off	SSB non-electrical fault	The direct clutch did not apply when SSB was commanded hydraulically on. DTC P2701 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0756 returns, REFER to: Diagnosis By Symptom .
P0757	Shift Solenoid "B" Stuck On	SSB non-electrical fault	The direct clutch did not release when SSB was commanded hydraulically off. DTC P2701 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0757 returns, REFER to: Diagnosis By Symptom .
P0758	Shift Solenoid "B" Electrical	SSB	SSB electrical circuit fault. DTC P0755, P0976 and/or P0977 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0759	Shift Solenoid "B" Intermittent	SSB	Intermittent circuit fault on SSB. CLEAR the DTC. Monitor SSPCB_F PID while wiggle testing the harness or road testing the vehicle. If DTC P0759 returns, GO to Pinpoint Test A
P0760	Shift Solenoid "C"	SSC	SSC open circuit. DTC P0763 may set, CLEAR the DTC. If DTC P0760 returns, GO to Pinpoint Test A
P0761	Shift Solenoid "C" Performance/Stuck Off	SSC non-electrical fault	The intermediate clutch did not apply when SSC was commanded on. DTC P2702 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0761 returns, REFER to: Diagnosis By Symptom .
P0762	Shift Solenoid "C" Stuck On	SSC non-electrical fault	The intermediate clutch did not release when SSC was commanded off. DTC P2702 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0762 returns, REFER to: Diagnosis By Symptom .
P0763	Shift Solenoid "C" Electrical	SSC	SSC electrical circuit fault. DTC P0760, P0979 and/or P0980 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0764	Shift Solenoid "C" Intermittent	SSC	Intermittent circuit fault on SSC. CLEAR the DTC. Monitor SSPCC_F PID while wiggle testing the harness or road testing the vehicle. If DTC P0764 returns, GO to Pinpoint Test A
P0765	Shift Solenoid "D"	SSD	SSD open circuit. DTC P0768 may set, CLEAR the DTC. If DTC P0765 returns, GO to Pinpoint Test A
P0766	Shift Solenoid "D" Performance/Stuck Off	SSD non-electrical fault	The low/reverse clutch did not apply when SSD was commanded on. DTC P2703 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0766 returns, REFER to: Diagnosis By Symptom .
P0767	Shift Solenoid "D" Stuck On	SSD non-electrical fault or Low One-Way clutch seized (holding in both directions)	The low/reverse clutch did not release when SSD was commanded off. CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0767 returns, REFER to: Diagnosis By Symptom .
P0768	Shift Solenoid "D" Electrical	SSD	SSD electrical circuit fault. DTC P0765, P0982 and/or P0983 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0769	Shift Solenoid "D" Intermittent	SSD	Intermittent circuit fault on SSD. CLEAR the DTC. Monitor SSPCD_F PID while wiggle testing the harness or road testing the vehicle. If DTC P0769 returns, GO to Pinpoint Test A
P0770	Shift Solenoid "E"	SSE	SSE open circuit. DTC P0773 may set, CLEAR the DTC. If DTC P0770 returns, GO to Pinpoint Test A
P0771	Shift Solenoid "E" Performance/Stuck Off	SSE non-electrical fault	The overdrive clutch did not apply when SSE was commanded hydraulically on. DTC P2704 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0771 returns, REFER to: Diagnosis By Symptom .
P0772	Shift Solenoid "E" Stuck On	SSE non-electrical fault	The overdrive clutch did not release when SSE was commanded hydraulically off. DTC P2704 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P0772 returns, REFER to: Diagnosis By Symptom .
P0773	Shift Solenoid "E" Electrical	SSE	SSE electrical circuit fault. DTC P0770, P0985 and/or P0986 may set. CLEAR the DTC. Service the more specific DTC first. GO to Pinpoint Test A
P0774	Shift Solenoid "E" Intermittent	SSE	Intermittent circuit fault on SSE. CLEAR the DTC. Monitor SSPCE_F PID while wiggle testing the harness or road testing the vehicle. If DTC P0774 returns, GO to Pinpoint Test A
P0882	TCM Power Input Signal Low	Battery	INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If DTC P0882 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P0883	TCM Power Input Signal High	Battery	CLEAR the DTC. If DTC P0883 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P0884	TCM Power Input Signal Intermittent	Battery	CLEAR the DTC. If DTC P0884 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P0885	TCM Power Relay Control Circuit Open	Battery	CLEAR the DTC. If DTC P0885 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P0960	Pressure Control Solenoid Control Circuit/Open	LPC	LPC solenoid open circuit. DTC P0748 may set, CLEAR the DTC. If DTC P0960 returns, GO to Pinpoint Test A
P0961	Pressure Control Solenoid Control Circuit Range/Performance	LPC	Intermittent short to ground circuit fault on LPC solenoid. CLEAR the DTC. Monitor LPC_F PID while wiggle testing the harness or road testing the vehicle. Service the more specific DTC first. GO to Pinpoint Test A
P0962	Pressure Control Solenoid Control Circuit Low	LPC	LPC solenoid short to ground. DTC P0748 may set, CLEAR the DTC. If DTC P0962 returns, GO to Pinpoint Test A
P0963	Pressure Control Solenoid Control Circuit High	LPC	LPC solenoid short to power. DTC P0748 may set, CLEAR the DTC. If DTC P0963 returns, GO to Pinpoint Test A
P0973	Shift Solenoid "A" Control Circuit Low	SSA	SSA short to ground. DTC P0753 may set, CLEAR the DTC. If DTC P0973 returns, GO to Pinpoint Test A
P0974	Shift Solenoid "A" Control Circuit High	SSA	SSA short to power. DTC P0748 may set, CLEAR the DTC. If DTC P0974 returns, GO to Pinpoint Test A
P0976	Shift Solenoid "B" Control Circuit Low	SSB	SSB short to ground. DTC P0758 may set, CLEAR the DTC. If DTC P0976 returns, GO to Pinpoint Test A
P0977	Shift Solenoid "B" Control Circuit High	SSB	SSB short to power. DTC P0758 may set, CLEAR the DTC. If DTC P0977 returns, GO to Pinpoint Test A
P0979	Shift Solenoid "C" Control Circuit Low	SSC	SSC short to ground. DTC P0763 may set, CLEAR the DTC. If DTC P0979 returns, GO to Pinpoint Test A
P0980	Shift Solenoid "C" Control Circuit High	SSC	SSC short to power. DTC P0763 may set, CLEAR the DTC. If DTC P0980 returns, GO to Pinpoint Test A
P0982	Shift Solenoid "D" Control Circuit Low	SSD	SSD short to ground. DTC P0768 may set, CLEAR the DTC. If DTC P0982 returns, GO to Pinpoint Test A
P0983	Shift Solenoid "D" Control Circuit High	SSD	SSD short to power. DTC P0768 may set, CLEAR the DTC. If DTC P0983 returns, GO to Pinpoint Test A
P0985	Shift Solenoid "E" Control Circuit Low	SSE	SSE short to ground. DTC P0773 may set, CLEAR the DTC. If DTC P0985 returns, GO to Pinpoint Test A
P0986	Shift Solenoid "E" Control Circuit High	SSE	SSE short to power. DTC P0773 may set, CLEAR the DTC. If DTC P0986 returns, GO to Pinpoint Test A
P1001	The KOER Not Able to Complete, KOER Aborted	TCM	RETRIEVE and RECORD all DTCs. REPAIR any self-test or CM DTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the TCM to the latest software. RERUN the KOER self-test. If the DTC returns, INSTALL a new TCM. REFER to: TRANSMISSION CONTROL MODULE (TCM) After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
P1397	System Voltage Out Of Self Test Range	TCM	INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RUN the KOEO self-test. If DTC P1397 returns, REFER to: Charging System - 6.7L Power Stroke Diesel .
P1501	Vehicle Speed Sensor Out Of Self Test Range	TCM	Vehicle speed not at 0.0 mph (km/h) during the KOEO and/or KOER self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. If DTC P1501 returns, REFER to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL
P1635	Tire/Axle Out Of Acceptable Range	TCM	Refer to the appropriate Engine Controls article.
P1636	Inductive Signature Chip Communication Error	TCM	CLEAR the DTC. If DTC P1636 returns, INSTALL a new TCM. REFER to: TRANSMISSION CONTROL MODULE (TCM) After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
P163E	Transmission Control Module Programming Error	TCM	CLEAR the DTC. REPROGRAM the original TCM with the latest software. If DTC P163F returns, INSTALL a new TCM. REFER to: TRANSMISSION CONTROL MODULE (TCM) After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
P163F	Transmission ID Block Corrupted, Not Programmed	TCM	CLEAR the DTC. REPROGRAM the original TCM with the latest software. If DTC P163F returns, INSTALL a new TCM. REFER to: TRANSMISSION CONTROL MODULE (TCM) After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download .
P1700	Transmission Intermittent Failure (failed to neutral)	Transmission	DTC P1700 is a non-electrical DTC and may be a main control body issue where the multiplex valve reverse pressure bleeds off too slow and causes the multiplex valve to get stuck in the wrong state. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom .
P1702	Transmission Range Sensor Circuit Intermittent	TR sensor	DTC P0706, P0707 and/or P0708 may set, CLEAR the DTC. If DTC P1702 returns, GO to Pinpoint Test C
P1705	Transmission Range Circuit Not Indicating Park/Neutral During Self Test	TR sensor	CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1705 returns, GO to Pinpoint Test C
P1711	Transmission Fluid Temperature Sensor Out Of Self Test Range	TFT sensor	CLEAR the DTC and RERUN the KOEO and KOER self-test.
P1744	Torque Converter Clutch Solenoid Performance	TCC non-electrical fault	The torque converter clutch failed the functional test. DTC P0741 or P2758 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . Service the more specific DTC first. REFER to: Diagnosis By Symptom .
P177F	Unable To Fully Engage Neutral	Transmission internal	This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. REFER to the appropriate Transmission procedure.
P1780	Transmission Control Switch (O/D Cancel) Circuit Out of Self-Test Range	TCS	CLEAR the DTC. If DTC P1780 returns, REFER to: External Controls .
P1783	Transmission Over Temperature Condition	Transmission	CLEAR the DTC. If DTC P1783 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwise REFER to: Transmission Cooling .
P1910	Reverse Lamp Control Circuit/Open	Reverse lamps	CLEAR the DTC. TEST system for normal operation. If DTC P1910 returns, REFER to DIAGNOSIS AND TESTING
P1921	Transmission Range Signal	TR sensor	The engine may not crank. DTC P0706, P0707 and/or P0708 may set. CLEAR the DTC. If DTC P1921 returns, CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1921 returns, GO to Pinpoint Test C
P2531	Ignition Switch Run Position Circuit Low	Ignition Switch	The TCM sets this DTC if low ignition run voltage is detected. GO to Pinpoint Test J
P2610	ECM/PCM Internal Engine Off Timer Performance	TCM	GO to Pinpoint Test K
P2669	Actuator Supply Voltage "B" Circuit Open	TCM	Power is routed through the Transmission Solenoid Power Control (TSPC) relay (inside the TCM) to all solenoids. If the power circuit to the transmission solenoids or the TSPC relay fails open, then all solenoids are failed electrically off. CHECK for open, short to ground or the transmission connector disconnected. The TSPC relay also disables power to the transmission solenoids when certain transmission DTCs are set. REPAIR as required. CLEAR the DTC. GO to Pinpoint Test A
P2700	Transmission Friction Element "A" Apply Time Range/Performance	Forward clutch system	DTC P2700 is a non-electrical DTC. DTC P0751 and/or P0752 may set. CLEAR the DTC. If DTC P2700 returns, REFER to: Diagnosis By Symptom .
P2701	Transmission Friction Element "B" Apply Time Range/Performance	Direct clutch system	DTC P2701 is a non-electrical DTC. DTC P0756 and/or P0757 may set. CLEAR the DTC. If DTC P2701 returns, REFER to: Diagnosis By Symptom .
P2702	Transmission Friction Element "C" Apply Time Range/Performance	Intermediate clutch system	DTC P2702 is a non-electrical DTC. DTC P0761 and/or P0762 may set. CLEAR the DTC. If DTC P2702 returns, REFER to: Diagnosis By Symptom .
P2703	Transmission Friction Element "D" Apply Time Range/Performance	Low reverse clutch system	DTC P2703 is a non-electrical DTC. DTC P0766 and/or P0768 may set. CLEAR the DTC. If DTC P2703 returns, REFER to: Diagnosis By Symptom .
P2704	Transmission Friction Element "E" Apply Time Range/Performance	Overdrive clutch system	DTC P2704 is a non-electrical DTC. DTC P0771 and/or P0772 may set. CLEAR the DTC. If DTC P2704 returns, REFER to: Diagnosis By Symptom .
P2705	Transmission Element "F" Apply Time Range/Performance	Low one way clutch	DTC P2705 is a non-electrical DTC. CLEAR the DTC. If DTC P2705 returns, REFER to: Diagnosis By Symptom .
P2758	Torque Converter Clutch Pressure Control Solenoid Stuck On	TCC non-electrical fault	The torque converter clutch did not release when TCC was commanded off. DTC P1744 may set, CLEAR the DTC and road test the vehicle. REFER to: Road Testing Vehicle . If DTC P2758 returns, REFER to: Diagnosis By Symptom .
P2760	Torque Converter Clutch Pressure Control Solenoid Intermittent	TCC	Intermittent TCC solenoid short to ground. CLEAR the DTC. Monitor TCC_F PID while wiggle testing the harness or road testing the vehicle. If DTC P2760 returns, GO to Pinpoint Test A
U0028	Vehicle communication bus A	CAN	CLEAR the DTC. RUN the Network Test. If the DTC returns, REFER to: Communications Network .
U0073	The PCM /TCM lost CAN communication to all modules.	CAN	CLEAR the DTC. RUN the Network Test. If the DTC returns, REFER to: Communications Network .
U0100	Lost communication with Engine Control Module (ECM) /PCM A	CAN	GO to Pinpoint Test F
U0102	Lost communication with Transfer Case Control Module (TCCM)	CAN	GO to Pinpoint Test G
U0115	Lost communication with ECM /PCM B	CAN	GO to Pinpoint Test F
U0121	Lost communication with the ABS control module	CAN	GO to Pinpoint Test G
U0133	Lost communication with active roll control module	CAN	GO to Pinpoint Test H
U0140	Lost Communication with BCM	CAN	GO to Pinpoint Test H
U0141	Lost Communication with BCM A	CAN	GO to Pinpoint Test H
U0155	Lost Communication with Instrument Panel Cluster (IPC) control module	CAN	GO to Pinpoint Test I
U0294	Lost Communication with Powertrain Control Monitor Module	CAN	If equipped.
U0401	Invalid Data Received from ECM /PCM A	CAN	This DTC sets when the TCM fails to receive data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to: Electronic Engine Controls . If no DTCs are present in the PCM, DIAGNOSE the observable symptom.
U0415	Invalid Data Received from Anti-Lock Brake System (ABS) control module	CAN	This DTC sets when the TCM fails to receive wheel speed data from the ABS. RETRIEVE and REPAIR all non-network DTCs in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) and Stability Control . If no DTCs are present in the ABS module, DIAGNOSE the observable symptom.
U0422	Invalid Data Received from BCM: No Sub-Type Information	CAN	This DTC sets when the TCM fails to receive data from the BCM. RETRIEVE and REPAIR all non-network DTCs in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no DTCs are present in the BCM, DIAGNOSE the observable symptom.