Installing the left cylinder head

CAUTION: Heavy component .
Heavy components can lead to injury or damage .

Remove and install heavy components with the aid of another person/other persons.

CAUTION: Swirling dirt particles caused by compressed air .
Injury hazard!

Collect dirt particles, e.g. when blowing out, use cloth to do so.
Wear safety goggles.

NOTE: RISK OF DAMAGE
Damage to guide rails .
The application of great force can damage the guide rails of the timing chain .

When removing and installing the cylinder head, make sure that the cylinder head does not damage the guide rail.

NOTE: RISK OF DAMAGE
Damage to the surface .
The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage .

Do not use any metal-cutting tools.

NOTE: TECHNICAL INFORMATION
When assembling, it is essential to observe screwing sequences and tightening torques.
Failure to comply with the regulations can lead to leaks and damage.

Check if there are fluids or foreign materials present in the cylinder bores, remove fluids or foreign materials where required.

Courtesy of BMW OF NORTH AMERICA, INC.
Check the fitting sleeves (1) for correct seating and damage and replace if necessary.

Courtesy of BMW OF NORTH AMERICA, INC.
Close the oil hole in the area (1) with a plug of the classification B from the set of special tools 2 364 711 .

Courtesy of BMW OF NORTH AMERICA, INC.
Clean sealing surface (1) with special tool 0 495 103 (11 4 471) from the set of special tools 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.
Clean sealing surface (1) with special tool 0 495 104 (11 4 472) from the set of special tools 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
If there are foreign bodies or fluids present in the bores, the tightening torque values can be falsified.
Clean bores of cylinder head bolts (1) with compressed air.

Courtesy of BMW OF NORTH AMERICA, INC.
Clean sealing surface (1) with special tool 0 495 103 (11 4 471) from the set of special tools 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.
Clean sealing surface (1) with special tool 0 495 104 (11 4 472) from the set of special tools 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.
Replace cylinder head gasket (1).
Parts: Cylinder head gasket
Replace screws.
Parts: screw
Position cylinder head gasket (1) on the fitting sleeves on the engine block.
If the cylinder head was reworked, then a thicker cylinder head gasket is to be installed .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The work must be performed with vehicle care to prevent component damage.
Attach the special tool 0 490 561 (11 0 000) on the retaining tab (1) and on the special tool 0 494 116 (11 8 352) from the set of special tools 0 493 997 (11 8 350).
Position cylinder head with a workshop crane.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The work must be performed with vehicle care to prevent component damage.
Carefully insert the cylinder head with the help of a workshop crane and 3 auxiliary persons and install it.
When feeding in and installing the cylinder head (1), make sure that the slide rails and timing chain (2) are not damaged.
Detach the special tool 0 490 567 (11 0 020) on the retaining tab (1) and on the special tool 0 494 116 (11 8 352) from the set of special tools 0 493 997 (11 8 350).

Courtesy of BMW OF NORTH AMERICA, INC.

Tightening left cylinder head

Tightening the left cylinder head

Fig 1: Cylinder Head Screws Tightening Sequence
Courtesy of BMW OF NORTH AMERICA, INC.

Tighten screws in the order (1) to (10).

TIGHTENING TORQUE SPECIFICATIONS

Cylinder head bolt
M11 Replace screws.	Joining torque 30 Nm
	Angle of rotation 90°
	Angle of rotation 140°

Release the screws (1) on the special tool 0 494 116 (11 8 352) from the set of special tools 0 493 997 (11 8 350) from the cylinder head.
Remove the special tool 0 494 116 (11 8 352) from the set of special tools 0 493 997 (11 8 350).

Courtesy of BMW OF NORTH AMERICA, INC.

Secure the screws (1) to the timing case cover.

TIGHTENING TORQUE SPECIFICATIONS

Cylinder head bolt to timing case cover
M8x30	tightening torque 23 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Replace sealing ring (1).
Parts: Sealing ring
Position sealing ring (1) on the bearing screw (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Position the slide rail.

Tighten the screw of the slide rail on the cylinder head of cylinder bank (1).

TIGHTENING TORQUE SPECIFICATIONS

Slide rail to cylinder head
Bearing screw	tightening torque 25 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Slide on the coolant hose.
Tighten the hose clamp (1).

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: To provide a better overview: Schematic diagram with partially hidden components.
Attach the wiring harness mountings (1) below the intake plenum (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Connect the connector (1) to the servomotor and lock audibly.
Connect the connector (2) to the pressure sensor on the intake plenum and lock audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Route the coolant line (1) between cylinder head and intake plenum.

Courtesy of BMW OF NORTH AMERICA, INC.
Install the heat shield (2) on the rear of the cylinder head.
Tighten down screws (1).
TIGHTENING TORQUE SPECIFICATIONS

Heat protection plate

M6x16 tightening torque
10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING BOTH LEFT VANOS ADJUSTERS .
Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
Refer to INSTALLING THE SEALING CAP ON THE CYLINDER HEAD OF CYLINDER BANK 2 .
Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
Refer to INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2 .
Refer to INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
Refer to INSTALLING FRONT HEAT SHIELD .
Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
Refer to FASTENING THE WIRING HARNESS SECTION TO THE LEFT CYLINDER HEAD COVER .
Refer to INSTALLING THE IGNITION COILS OF CYLINDER 5-8 .
Refer to INSTALLING THE IGNITION COIL OF CYLINDER 1 .
Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
Refer to INSTALLING THE BELT TENSIONER .
Refer to INSTALLING COOLANT PUMPS .
Refer to INSTALLING THE LEFT AND RIGHT EXHAUST TURBOCHARGER .
Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
Refer to INSTALLING DRIVE BELT .
Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to CONNECTING THE COOLANT HOSES TO THE HIGH-TEMPERATURE COOLANT RADIATOR .
Refer to INSTALLING RIGHT CLEAN AIR PIPE .
Refer to INSTALLING LEFT CLEAN AIR PIPE .
Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT PUMP .
Refer to INSTALLING FAN COWL .
Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 5 TO 8 .
Refer to INSTALLING RIGHT HEAT SHIELD .
Refer to INSTALLING LEFT HEAT SHIELD .
Refer to TIGHTENING SCREW BETWEEN THE LEFT AND RIGHT HEAT SHIELD .
Refer to INSTALLING HEAT SHIELD, TOP .
Refer to INSTALLING THE RIGHT-HAND ENGINE VENTILATION LINE AND THE CRANKCASE VENTILATION INTAKE PIPE .
Refer to INSTALLING THE LEFT ENGINE VENTILATION LINE .
Refer to INSTALLING THE RIGHT MONITORING OXYGEN SENSOR .
Refer to INSTALLING OXYGEN SENSOR ON THE LEFT .
Refer to INSTALLING THE RIGHT UNFILTERED-AIR DUCT .
Refer to INSTALLING THE LEFT UNFILTERED-AIR DUCT .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to INSTALLING UPPER CROSS CONNECTION .
Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT , and INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE TOP RIGHT .
Refer to INSTALLING COVER FOR THE RIGHT DME CONTROL UNIT .
Refer to INSTALLING THE HOLDER FOR THE DME CONTROL UNIT ON THE LEFT .
Refer to INSTALLING THE DME CONTROL UNIT OF CYLINDERS 5 TO 8 .
Refer to INSTALLING COVER FOR THE LEFT DME CONTROL UNIT .
Refer to INSTALLING THE TENSION STRUT ON THE RIGHT SHOCK TOWER .
Refer to INSTALLING INTAKE FILTER HOUSING .
Refer to INSTALLING THE RIGHT STRUT BRACE .
Refer to INSTALLING THE STRUT BRACE .
Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
Refer to INSTALL ACOUSTIC COVER .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .
Refer to INSTALLING EXHAUST SYSTEM .
Refer to INSTALLING THE STIFFENING PLATE .
Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to FILLING AND VENTING THE HIGH-TEMPERATURE COOLANT CIRCUIT .

Heat protection plate
M6x16	tightening torque 10 Nm