Installing the rear timing case cover

Courtesy of BMW OF NORTH AMERICA, INC.

• Clean sealing surfaces (1)  with special tool 0 495 102 (11 4 470) .
• Clean the sealing surface (1)  with brake cleaner.
  CONSUMABLE SPECIFICATION
  
  

  Brake cleaner 2.0	500 ml, Spray can	83192365214
  	20, Canister	83192365215

Courtesy of BMW OF NORTH AMERICA, INC.

• Clean sealing surfaces (1)  with special tool 0 495 102 (11 4 470) .
• Clean the sealing surface (1)  with brake cleaner.
  CONSUMABLE SPECIFICATION
  
  

  Brake cleaner 2.0	500 ml, Spray can	83192365214
  	20, Canister	83192365215

• Position the timing case cover (1)  underneath.
• Position the punch inside in the crankshaft sealing ring (2)  .
• Remove the crankshaft sealing ring (2)  outwards in arrow direction.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check the fitting sleeves (1)  for damage, replace if necessary.
• Check for correct fit of fitting sleeves (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Have the special tool 2 469 803 ready.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the sealing compound (1)  as shown on the special tool 2 469 803 .

  Parts:  Sealant

  Courtesy of BMW OF NORTH AMERICA, INC.

• Apply the sealing compound in area (1)  along the inner edge.

  Courtesy of BMW OF NORTH AMERICA, INC.

  SEALING COMPOUND SPECIFICATION
  
  

  Loctite 5970 liquid sealing compound  Processing time <10 minutes at room temperature

  50 ml, Cartridge

  83190404517

  TECHNICAL DATA SPECIFICATION
  
  

  Height of the sealing bead
  	2.0 mm... 2.5 mm

• Replace screws (1)  to (11)  .

  Parts:  Screws

• Carefully mount the timing case cover (A)  .
• Tighten the screws in the sequence (1)  to (11)  with the special tool 0 490 504 (00 9 120) .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Rear timing case cover on crankcase
  M6 x 31 Replace screws.	Joining torque	8 Nm
  	Angle of rotation	90°

  Fig 1: Timing Case Cover Screws Tightening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.
• Connect connectors (1)  and lock.

  The connector (1)  must engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

Installing the rear crankshaft seal 

• Install special tool 0 496 137 (11 8 815) on the crankshaft.
• Pull off crankshaft sealing ring (1)  in the arrow direction using special tool 0 496 137 (11 8 815) so that crankshaft sealing ring (1)  rests all around the timing case cover.
• Guide the special tool 0 496 137 (11 8 815) out and remove.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure special tool 0 494 029 (11 9 182)  to the crankshaft using special tool 0 494 031 (11 9 184)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect special tool 2 360 215  to special tool 0 494 028 (11 9 181)  in the arrow direction.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position special tools 0 494 028 (11 9 181)  and 2 360 215  and bring into contact with the crankshaft seal in connection with special tool 0 494 030 (11 9 183)  .
• Check the freedom of movement between the special tool 2 360 215  and the crankshaft sensor during installation.
• Screw in the crankshaft sealing ring up to the stop of the timing case cover using special tool 2 360 215  .

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to REFITTING OIL PAN .
• Refer to INSTALLING THE FLYWHEEL .
• Refer to SEALING THE OIL DUCT .
• Refer to CLEANING SEALING SURFACES .
• Refer to INSTALLING THE CYLINDER HEAD GASKET .
• Refer to BLOCKING THE CRANKSHAFT IN THE TDC FIRING POSITION OF CYLINDER 1 .
• Refer to INSTALLING THE CYLINDER HEAD .
• Refer to ADJUSTING THE CAMSHAFTS WITH THE SPECIAL TOOL .
• Refer to INSTALLING THE INTAKE ADJUSTER .
• Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
• Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
• Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
• Refer to PRE-TENSIONING THE TIMING CHAIN WITH THE SPECIAL TOOL .
• Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
• Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
• Refer to DISASSEMBLING ALL SPECIAL TOOLS .
• Refer to INSTALLING CHAIN TENSIONER .
• Refer to CHECKING THE TIMINGS OF THE CAMSHAFT .
• Refer to INSTALLING THE COOLANT LINE BETWEEN THE CYLINDER HEAD AND THE COOLANT PUMP .
• Refer to INSTALLING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING CYLINDER HEAD COVER .
• Refer to INSTALLING BOTH ACTUATORS .
• Refer to PREPARING THE INJECTORS FOR INSTALLATION .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL WITH INJECTORS OF THE CYLINDERS 4 TO 6 .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL WITH INJECTORS OF THE CYLINDERS 1 TO 3 .
• Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE PUMP AND THE HIGH-PRESSURE RAIL .
• Refer to INSTALLING HIGH PRESSURE PUMP .
• Refer to INSTALLING ALL SPARK PLUGS .
• Refer to INSTALLING ALL IGNITION COILS .
• Refer to INSTALLING CATALYTIC CONVERTER .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
• Refer to INSTALLING LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE INTAKE PLENUM .
• Refer to INSTALLING THE TANK VENT VALVE .
• Refer to INSTALLING ENGINE VENTILATION LINE .
• Refer to INSTALLING ACOUSTIC COVER AT REAR .
• Refer to FILLING ENGINE OIL .
• Refer to OPENING THE OIL FILLER CAP .
• Refer to REMOVING THE ENGINE FROM THE ASSEMBLY JIG .
• Refer to MOUNTING THE ENGINE ON THE FRONT AXLE .
• Refer to INSTALLING THE COMPLETE FRONT AXLE WITH THE ENGINE AND TRANSMISSION .