Installing the sealing cap on the cylinder head of cylinder bank 2

• Replace the seal (1)  .

  Parts:  Seal

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the sealing cap (2)  on the cylinder head.
• Tighten down screws (1)  .

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
• Refer to SECURING THE INTAKE PIPE AT THE FRONT .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to SECURING THE WIRING HARNESS SECTION FROM THE CYLINDER HEAD COVER ON THE LEFT .
• Refer to INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE INTAKE PIPE OF THE ENGINE VENTILATION LINE .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING THE BELT TENSIONER .
• Refer to INSTALLING COOLANT PUMPS .
• Refer to INSTALLING DRIVE BELT .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING THE LEFT ENGINE VENTILATION LINE (PARTIALLY REMOVED) .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT PUMP .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE CARRIER PLATE .
• Refer to INSTALLING THE CATALYTIC CONVERTER OF CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
• Refer to INSTALLING THE LEFT OXYGEN SENSOR MONITOR .
• Refer to INSTALLING HEAT SHIELD, TOP .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
• Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
• Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .
• Refer to CONNECTING THE COOLANT HOSES TO THE HIGH-TEMPERATURE COOLANT RADIATOR .
• Refer to PREPARING THE INJECTORS FOR INSTALLATION .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
• Refer to CONNECTING THE CONNECTOR OF THE INJECTORS OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
• Refer to INSTALLING THE SOUND INSULATION OF THE INJECTORS, LEFT .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING THE RIGHT AND LEFT UNFILTERED-AIR DUCT .
• Refer to INSTALLING THE IGNITION COILS OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 1 .
• Refer to INSTALLING BRACKET FOR RIGHT INTAKE SILENCER .
• Refer to INSTALLING BOTH INTAKE FILTER HOUSING .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
• Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
• Refer to EVACUATING AND CHARGING CONDITIONING .