Installing the engine wiring harness for the sensor system 1

Engine wiring harness for sensor system 1 

Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in and install the engine wiring harness (1) for sensor system 1.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in and install the engine wiring harness (2) for sensor system 1.
• Connect connectors (1) and lock.

  The connectors (1) must engage audibly.

• Secure the clamps (arrows).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in and install the engine wiring harness (2) for sensor system 1.
• Connect connectors (1) and lock.

  The connectors (1) must engage audibly.

• Secure the clamps (arrows).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in and install the engine wiring harness (2) for sensor system 1.
• Tighten down screws (1).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Cable bracket on rear cylinder head/transmission
  M6 x 20	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in the wiring harness section (2) and install.
• Make sure the detent (arrow) engages audibly.
• Tighten down screws (1).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Cable bracket on rear cylinder head/transmission
  M6 x 20	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1) and (2) and lock.

  The connectors (1) and (2) must audibly engage.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (3) and lock.

  The connector (3) must engage audibly.

• Connect connectors (2) and lock.

  The connectors (2) must engage audibly.

• Connect connectors (1) and lock.

  The connectors (1) must engage audibly.

• Secure the clamps (arrows).

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
• Refer to RAISING THE FRONT AXLE SUPPORT AND FASTEN IT
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
• Refer to FASTENING ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT
• Refer to IF INSTALLED: CONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
• Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR
• Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
• Refer to INSTALLING STEERING SHAFT AT BOTTOM ON STEERING GEAR
• Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
• Refer to INSTALLING THE INTAKE PLENUM
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING ALL IGNITION COILS .
• Refer to INSTALLING THE TANK VENT VALVE .
• Refer to INSTALL CONTROL UNIT BRACKET 
• Refer to INSTALL THE INTEGRATED POWER SUPPLY MODULE (PDM) 
• Refer to INSTALLING THE DME CONTROL UNIT
• Refer to INSTALLING ACOUSTIC COVER AT REAR
• Refer to INSTALLING THE SECOND END PANEL UNDERNEATH .
• Refer to INSTALLING THE COWL UPPER PART .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING RESONATOR
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING THE RIGHT FRONT-END STRUT .
• Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to RECONNECTING ALL BATTERY GROUND LEADS .
• Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .