Install mechanics

• Feed in and position connecting pipe (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• The drive cables (1) have a color coding at the end (2).
• Assignment of color coding:

  Color	Position
  Blue	Front left
  White	Front right
  Green	Rear left
  red	Rear right

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in drive cable for the roller sunblind (1) into the guide (2) and push in until it stops.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in drive cable (2) for the mechanics (1) into the guide (3).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in the drive cable (2) further and position mechanics (1) on the roof frame.
• Ensure that the driver for the roller sunblind (3) and the guides for the drive cable (4) are correctly fed into the mechanics (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the screws (2).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Guide rail on bodyshell
  Screw	tightening torque	10 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten nuts (3).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Guide rail on bodyshell
  Nut	Joining torque	1.5 Nm
  	Angle of rotation	120°

• Tighten down screw (1).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Guide sleeve on mechanics
  Screw	tightening torque	4 Nm

• Connect plug connection (1) and lock.
• Clip in the wiring harness (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

  Installing front drive system for roller sunblind 

• Guide in the drive of the front roller sunblinds (3) and position it correctly.
• Tighten the screws (2).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Drive on body
  Screw	tightening torque	8.60 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1) and lock.

  Installing drive motor for glass slide/tilt sunroof cover 

• Feed in the motor for the glass slide/tilt roof panel (3) and position it correctly.
• Tighten the screws (2).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Drive on body
  Screw	tightening torque	8.60 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1) and lock.

Follow-up work 

• Refer to INSTALLING THE ROLLING MODULE .
• Refer to PARTIALLY INSTALLING THE HEAD AIRBAG .
• Refer to CHECKING THE ROLLER SUNBLIND AND THE GLASS ROOF FOR FUNCTION .
• Refer to INSTALLING THE HEADLINING (LOWERED WITH PANORAMIC GLASS SUNROOF) .
• Refer to INSTALLING INTERIOR ROOF LIGHT .
• Refer to INSTALLING THE GRAB HANDLE AT THE REAR LEFT AND RIGHT .
• Refer to INSTALLING ROOF FUNCTION CENTER (FZD) .
• Refer to INSTALLING THE LEFT AND RIGHT FRONT VANITY MIRROR LIGHT .
• Refer to INSTALLING BOTH SUN VISORS AND COUNTER SUPPORTS .
• Refer to INSTALLING THE LEFT AND RIGHT HANDS-FREE MICROPHONE .
• Refer to INSTALLING THE C-PILLAR TRIM PANEL ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE LEFT AND RIGHT SEAT BELT FINISHER STRIP .
• Refer to INSTALLING BOTH BACKREST SIDE SECTIONS .
• Refer to PARTIALLY INSTALLING BOTH B-PILLAR TRIM PANELS AT TOP .
• Refer to INSTALLING A-PILLAR TRIM PANEL, LEFT AND RIGHT .
• Refer to INSTALLING THE PANORAMA ROOF COVER .
• Refer to CHECKING THE ADJUSTMENT OF THE PANORAMA GLASS ROOF .
• Refer to ADJUSTING THE PANORAMA ROOF COVER .
• Refer to INSTALLING SEALING RING FOR THE PANORAMIC ROOF INSIDE .
• Refer to INITIALIZING PANORAMA GLASS ROOF .