11 41 115 Removing and installing/replacing hydraulic valve for oil-pressure control (for oil pressure control) (Vehicles with automatic transmission): Notes
WARNING: This page is about a different car, the 2018 BMW 340i, 2017 BMW 340i, and 2016 BMW 340i. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
Hot fluids.
Risk of scalding!
Risk of scalding!
- Conduct all work in the vehicle wearing appropriate personal protective equipment only.
CAUTION:
Materials harmful to health.
Contact with fluids harmful to health!
Contact with fluids harmful to health!
- Note and follow safety instructions on containers.
- Conduct all work in appropriate personal protective equipment only.
NOTE:
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.
Preliminary work
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS
- Refer to REMOVING THE ACOUSTIC COVER
- Refer to REMOVING THE FRONT UNDERBODY PROTECTION
- Refer to REMOVING THE REAR UNDERBODY PROTECTION
- Remove the support for the underbody protection
- Refer to REMOVING THE PROTECTIVE PLATE FOR THE FUEL LINES
- Refer to DRAINING THE COOLANT FROM THE HIGH-TEMPERATURE COOLING SYSTEM
- Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM
- Refer to UNINSTALLING COVER FOR THE DME CONTROL UNIT
- Refer to DISCONNECTING THE CONNECTOR FROM THE DME CONTROL UNIT AND FROM THE POWER DISTRIBUTION MODULE (PDM)
- Refer to REMOVING THE DME CONTROL UNIT
- Refer to REMOVING THE INTEGRATED POWER SUPPLY MODULE (PDM)
- Refer to REMOVING THE HOLDER FOR THE DIGITAL MOTOR ELECTRONICS-CONTROL UNIT
- Refer to REMOVING TRAILING LINK AT SPRING STRUT DOME
- Remove the sound insulation on the bulkhead upper part at the center
- Refer to REMOVING ACOUSTIC COVER AT REAR
- Refer to REMOVING TANK VENT VALVE
- Unlock and disconnect connector (1). Loosen screws (2). Remove charge air line from throttle body and place to one side.
- Refer to REMOVING THE INTAKE PLENUM
- Refer to REMOVING TRANSMISSION OIL COOLER
Follow-up work
- Refer to INSTALLING TRANSMISSION OIL COOLER
- Refer to INSTALLING THE INTAKE PLENUM
- Fasten charge air line to the throttle body
- Refer to INSTALLING THE TANK VENT VALVE
- Refer to INSTALLING ACOUSTIC COVER AT REAR
- Install the sound insulation on the bulkhead upper part at the center
- Install tension strut on spring strut dome. Jointing torque: 56 Nm, angle of rotation: 90° NOTE: Replace screws.
- Refer to INSTALLING THE HOLDER FOR THE DIGITAL MOTOR ELECTRONICS-CONTROL UNIT
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM)
- Refer to INSTALLING THE DME CONTROL UNIT
- Refer to CONNECTING THE CONNECTOR TO THE DME CONTROL UNIT AND THE POWER DISTRIBUTION BOX (PDM)
- Refer to INSTALLING ACOUSTIC COVER
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR OF THE LOW-TEMPERATURE COOLANT CIRCUIT
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR
- Install the protective plate for the fuel lines
- Refer to CONNECTING ALL BATTERY GROUND LEADS
- Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE
- Refer to BLEEDING THE HIGH-TEMPERATURE COOLANT SYSTEM
- Refer to BLEEDING THE LOW-TEMPERATURE COOLING SYSTEM
- Check transmission oil level and TOP-UP OIL as necessary.
- Install the support for the underbody protection. Tightening torque: 3Nm.
- Install underbody protection at rear
- Install the front underbody protection